公司技术保密协议范本(20篇)

企业借款申请书代借款借据

以下是小编为大家收集的合同范本，仅供参考!

_________年_________月_________日 企业名称 开户银行及帐号 年、季度借款计划 已借金额 申请借款金额(大写) 借款期限 借款种类 借款用途 借款原因 还 款 计 划 借款批准后以本申请书作为借款借据 此致 中国工商银行××分行 借款单位盖章 法人代表章 主管部门 意见

_________年_________月_________日

企业名称

开户银行及帐号

年、季度借款计划

已借金额

申请借款金额(大写)

借款期限

借款种类

借款用途

借款原因

还 款 计 划

借款批准后以本申请书作为借款借据

此致 中国工商银行××分行 借款单位盖章 法人代表章

主管部门 意见 盖章

银行 审查 意见

批准金额(大写)

批准期限

法人代表章 经办人章 年 月 日

蓄电池技术质量验收协议

注：参考里程是在环境温度25±5℃，车、路况正常，最高车速20km/h，载重负荷不大于75kg的条件下进行的；且和电机效率、控制器控制参数等整车配制有关。

4.2.3 乙方产品在正常使用条件下质保期

（1）“普通铅酸型”和“ⅰ代胶体环保型”出厂_________个月；使用_________个月。

（2）“ⅱ代胶体环保型”出厂_________个月；使用_________个月。质保期二个条件只要达到一条都视为超过质保期，在质保期内若发生下列问题：①短路②断路③反极④大面积脱粉，经甲、乙双方检查确认后电池容量末达到标称容量的60%，由乙方负责修理或调换，否则不予承保。（其它规格型号的电池质保期双方另行订立）

4.2.4 乙方每月根据甲方上月退回的经双方确认确属乙方责任的电池数量，如数向甲方返还相同规格型号的电池：

（1）电池出_________个月以内如出现容量明显下降至额定容量80％以下（或漏酸、短路等故障），乙方负责调换全新电池，并重新计算质保期；

（2）电池出厂_________个月以外且在质保期内如出现容量明显下降至额定容量60%以下（或漏酸、短路等故障），乙方负责调换标称容量在80%以上的维护电池， 三包期从原使用电池的出厂日期起累计续保。

4.2.5 乙方负责回收甲方过质保期的“华富”废旧电池，回收方法和价格另订。

4.2.6 乙方负责生产的电动车专用蓄电池由中国人民保险公司承担产品信誉和产品责任保险。

4.3 本协议为双方供货合同的附件，具有同等效力，履行地为_________，解释权为乙方所有。

5.其它约定

_________

_________

甲方（签章）：_________ 乙方（签章）：_________

代表：_________ 代表：_________

电话：_________ 电话：_________

传真：_________ 传真：_________

日期：_________年__月__日 日期：_________年__月__日

转让技术秘密和补偿贸易合作生产合同

甲 方：____________________________________

地 址：____________ 邮码：____________ 电话：____________

法定代表人：____________ 职务：____________

乙 方：____________________________________

地 址：____________ 邮码：____________ 电话：____________

法定代表人：____________ 职务：____________

甲、乙双方在平等、互利基础上，经充分协商，达成如下协议，以期遵守。

第一条 技术名称、资料

1.技术名称、权属：

2.“技术文件资料”的定义、范围及交付：

（1）一般技术资料包括：

（2）产品设计图纸：

（3）生产技术资料：

（4）资料的修改：

（5）资料的提供方式：

a.对一般技术文件应提供三份蓝图或同等数量的清晰的复制图；

b.对产品设计图纸应提供一份生产底图及两份蓝图；

c.对生产技术资料应提供两份蓝图；

d.对已提供过的完全相同的重复资料，可免于提供，但需在清单中予以注明。

（6）资料的交付进度：

a.根据资料定义的规定，在签订合同后____天需交付合同产品的全部技术资料和图纸；

b.根据资料定义的规定，在签订合同后于____年____月____日前需向________交付合同产品的全部技术资料和图纸。

第二条 合作期限

1.以补偿贸易进行使用生产期限为____年，____年后若合资经营条件不成熟，则可延长合作生产期限，但最长不得超过____年。

第三条 转让技术秘密和技术文件

1.乙方提供合同产品的设计计算、产品图纸、制造工艺、质量控制和试验安装、调试、运载及维修等有关合同产品的全部技术资料，必须和目前使用的资料内容相同。

2.合同产品资料的审核和验证： 乙方对提供甲方的产品设计图纸、制造技术资料的完整性、正确性、清晰性负责。

3.在合作生产期间，甲方将以最优惠价格向乙方提供本项目市场不能提供的零部件。具体内容另行商定。

4.甲方保证向乙方转让的技术秘密和技术资料不受任何第三者的指控。

第四条 价格和支付方式

1.乙方向甲方支付技术秘密和技术资料费用期限如下： ____年____u.s.d（大写__________美元整） ____年____u.s.d（大写__________美元整） ____年起以后的2年中按每年净产值（即每年总产值扣除进口部分价值和税收费用后的产值）其提成费为____%.

2.合同签署生效后（30）天内，乙方按照由________银行提交的甲方下列单据，予以第一次支付总金额的________%，即________u.s.d.（大写：________美元整）。

（1）根据附件________要求，提供第一批资料的空运提单；

（2）经乙方确认的________银行出具不可撤销的保函正副本条一份；

（3）甲方的商业发票一式两份；

（4）甲方即期汇票一式两份。

3.于____年____月____日乙方收到甲方提交的下列单据后，予以第二次支付____年总金额的____%现金，即____u.s.d.（大写：________美元整）。

（1）按附件________要求于____年____月____日提供第二批资料空运提单；

（2）甲方商业发票一式两份；

共3页，当前第1页123

私营企业转让合同

转让方(甲方)： 身份证号码：

受让方(乙方)： 身份证号码：

(企业名称)(以下简称企业)于 年 月 日经 市工商行政管理局核准登记设立，由甲方个人投资并经营，企业全部财产属甲方个人所有，并拥有完全的处分权，企业出资额为人民币 万元。甲方愿意将其在企业的全部出资及与此相关的合法权益(以下称资产)转让给乙方，乙方愿意受让。现甲乙双方根据《中华人民共和国个人独资企业法》和《民法典》的规定，经协商一致，就转让资产事宜，达成如下协议：

一、转让价格及转让款的支付期限和方式：

1、甲方以人民币 万元的价格将其在企业的全部资产转让给乙方。

2、乙方应于本协议书生效之日起 日内以银行转帐(或现金支付)的方式一次性将上述款项支付给甲方。

二、保证：

甲方保证在对上述资产拥有所有权及完全处分权，甲方保证对所转让的财产，没有设置任何抵押、质押或担保，保证资产未被查封，并保证资产不受第三人之追索，否则，由此引起的所有责任，由甲方承担。

三、转让的效力：

自本协议书项下的转让完成之日起，乙方对企业全部财产享有所有权及相关的权益，并以其个人财产对企业债务承担无限责任。

四、违约责任：

1、本协议书一经生效，双方必须自觉履行，任何一方未按协议书的规定全面履行义务，应当依照法律和本协议书的规定承担责任。

2、如乙方不能按期支付转让款，每逾期一天，应向甲方支付逾期部分转让款的万分之一的违约金。如因乙方违约给甲方造成损失，乙方支付的违约金金额低于实际损失的，乙方必须另予以补偿。

3、如由于甲方的原因，致使乙方不能如期办理变更登记，或者严重影响乙方实现订立本协议书的目的，甲方应按照乙方已经支付的转让款的万分之一向乙方支付违约金。如因甲方违约给乙方造成损失，甲方支付的违约金金额低于实际损失的，甲方必须另予以补偿。

五、甲乙双方经协商一致，可以变更或解除本协议书。经协商变更或解除本协议书的，双方应另签订变更或解除协议书。

六、有关费用的负担：

在本次资产转让过程中发生的有关费用(如公证、评估或审计、工商变更登记等费用)，由甲方承担。

七、其他约定：

与本合同有效性、履行、违约及解除等有关争议，各方应友好协商解决。如果协商不成，则任何一方均可申请仲裁或向人民法院起诉。

八、合同生效的条件和日期：

本协议书经双方签署之日起生效。双方应于本协议书生效后依法向工商行政管理机关办理变更登记手续。

九、本协议书一式三份，甲乙双方各执一份，其余报有关部门。

转让方(甲方)：

年 月 日

受让方(乙方)：

年 月 日

甲方(单位)：___________________

注册号：___________________

地址：___________________

乙方(员工)：___________________

身份证号码：___________________

电话：___________________

鉴于乙方在甲方单位从事 岗位工作，期间已经(或将要)知悉甲方的商业秘密，并获得增进知识、经验、技能的机会，为明确乙方的保密义务，根据《中华人民共和国反不正当竞争法》、《劳动法》、《 劳动合同法》的相关规定，甲乙双方本着平等、自愿、公平和诚实信用的原则，订立本保密协议：

一、保密的内容和范围

甲乙双方确认，乙方承担保密义务的甲方商业秘密包括但不限于以下内容：

1.技术信息：技术信息的范围包括但不仅限于甲方的技术方案、工程设计、电路设计、制造方法、配方、工艺流程、技术指标、计算机软件、数据库、试验结果、图纸、样品、样机、模型、模具、操作手册、技术文档、涉及商业秘密的业务函电等。

2.经营信息：经营信息的范围包括但不仅限于甲方的客户名单、营销计划、采购资料、定价政策、不公开的财务资料、进货渠道、产销策略等。

3.甲方的交易秘密，包括但不限于商品产、供、销渠道，客户名单，买卖意向，成交或商谈的价格，商品性能、质量、数量、交货日期。

4.甲方的管理秘密，包括但不限于财务资料、人事资料、工资薪酬资料等。

5.甲方依照法律规定或有关协议的约定，对外承担保密义务的事项。

6.乙方在从职期间因工作关系而获得、交换的保密性信息以及其他一切与甲方事务有关的保密信息。

二、保密义务

对甲方的商业秘密，乙方承担以下义务：

1.不得刺探与本职工作或本身业务无关的甲方商业秘密;

2.不得向任何第三人披露甲方的商业秘密;

3.不得使任何第三人(包括甲方单位内部员工)获得、使用或计划使用甲方商业秘密信息，即除了得到甲方单位指示和在业务需要的程度范围内向应该知道上述内容的单位内部员工或本单位外业务单位进行保密内容交流外，不得直接或间接向单位内部、外部的人员泄露商业秘密信息;

4.不得允许(出借、赠与、出租、转让等方式处分甲方商业秘密的行为皆属于“允许”)或协助任何第三人使用甲方商业秘密信息;

5.不得为自己利益使用或计划使用;

6.不得复制或公开包含甲方单位商业秘密内容的文件、信函、正本、副本、磁盘、光盘等;

7.因工作保管、接触的有关单位的文件应妥善保存，未经许可不得超出工作范围使用，如发现商业秘密被泄露或因自己过失泄露的，应采取有效措施防止泄密进一步扩大，并及时向甲方报告;

8.乙方同意：因职务创造和构思的有关技术秘密或经营秘密，将向甲方及时汇报，并以书面形式做出报告，该职务成果归属甲方;

9.在商业秘密的个别部分或个别要素已被公知，但尚未使商业秘密的其他部分或整体成为公知知识，以致商业秘密没有丧失价值的情况下，乙方应承担仍属秘密信息部分的保密义务，不得使用该部分信息或诱导第三人通过收集公开信息以整理出甲方的商业秘密。

三、保密期限

甲乙双方确认，乙方的保密义务自甲方盖章和乙方签字之日起开始，至上述商业秘密公开或被公众知悉时止。乙方的保密义务并不因劳动合同的解除而免除。

四、违约责任

甲乙双方商定，如乙方违反上述各项义务而损害甲方利益，按照以下方法承担违约责任：

1.若乙方不履行本协议所规定的保密义务，应一次性向甲方支付违约金人民币 万元;

2.若因乙方前款的违约行为造成甲方损失的，乙方应承担赔偿责任(如乙方已经支付违约金的，应予以扣除)，具体损失赔偿标准为：(1)损失赔偿额为甲方因乙方的违约行为所受到的实际经济损失，包括甲方为开发、培植有关商业秘密所投入的费用，因乙方的违约行为导致甲方产品销售量减少的金额，

以及依靠商业秘密取得的利润减少金额等。(2)依照(1)款计算方法难以计算的，损失赔偿额为乙方因违约行为所获得的全部利润。(3)甲方因调查乙方违约行为而支付的合理费用，由乙方承担;(4)因乙方违约行为侵犯了甲方商业秘密权利的，甲方可选择根据本协议“第四条1、2款”的要求乙方承担违约责任，也可根据国家法律、法规要求乙方承担侵权责任。

3.乙方严重侵犯甲方的商业秘密，给甲方造成严重损失的，甲方可依据我国法律的有关规定，选择移送司法机关依法办理。

五、争议的解决方法

因执行本协议发生纠纷，可由双方协商解决或共同委托双方认可的第三方调解。有一方不愿协商、调解或协商、调解不成的，任何一方都有提起诉讼的权利。提起诉讼的法院为 。

六、其他

1. 本协议的任何修改必须经过双方的书面同意，协议的部分修改或部分无效并不影响其他部分的效力。

2. 本协议一式二份，甲方乙方各执一份，协议自双方签订之日起生效。

3. 本协议签订地为 。

4. 双方确认，在签订本协议前已经详细阅读过本保密协议，并确认对本协议中各条款的理解无异议。

(以下无正文)

甲方(盖章)：___________________ 乙方(签字)：___________________

法定代表人：___________________

日期： 年 月 日 日期： 年 月 日

技术合同：技术培训合同

委托方：_________

法定代表人或负责人：_________

服务方：_________

法定代表人或负责人：_________

根据《中华人民共和国合同法》的有关规定，经双方当事人协商一致，签订本合同。

第一条 项目名称

_________。

第二条 培训的内容和要求

_________。

第三条 培训计划、进度、期限

_________。

第四条 培训地点和方式

_________。

第五条 服务方(教师)的资历和水平

_________。

第六条 学员的人数和质量

_________。

第七条 教员、学员的食宿、交通、医疗费用的支付和安排

_________。

第八条 报酬及其支付方式

_________。

第九条 委托方的违约责任

1.委托方未按合同提供培训条件，影响合同履行的，约定的报酬仍应如数支付;

2.擅自将服务方要求保密的技术资料引用、发表和提供给第三方，应支付数额为_________的违约金;

第十条 服务方的违约责任：

1.服务方未按合同制订培训计划，影响培训工作质量的，应当减收_________%的报酬;

2.服务方提供的师资不符合合同要求，服务方有义务予以重新配备;未按合同规定完成培训工作的，应免收报酬。

第十一条 保密条款

当事人双方应对下列技术资料承担保密义务：

_________。

第十二条 技术成果归属

在履行合同过程中，服务方利用委托方提供的技术资料和工作条件所完成的新的技术成果，属于服务方;委托方利用服务方的工作成果所完成的新技术成果，属于委托方。对新的技术成果享有就该技术成果取得的精神权利(如获得奖金、奖章、荣誉证书的权利)、经济权利(如专利权、非专利技术的转让权，使用权等)和其它利益。

第十三条 本合同争议的解决办法

_________。

本合同自双方当事人签字、盖章后生效。

委托方(盖章)：_________ 服务方(盖章)：_________

负责人(或授权代表)(签字)：_________负责人(或授权代表)(签字)：_________

开户银行：_________ 开户银行：_________

帐号：_________ 帐号：_________

担保人(名称)(盖章)：_________ 担保人(名称)(盖章)：_________

_________年____月____日 _________年____月____日

签订地点：_________ 签订地点：_________

歇后语竞猜：二三四五六七八九 —— 〖查看答案〗

企业类赠与合同模板

企业类赠与合同

甲方(赠与方)：_________(名称)

法定代表人或负责人：_________

乙方(受赠人)：_________(名称)

法定代表人或负责人：_________

双方根据《中华人民共和国合同法》就赠与事项达成如下协议：

1.赠与标的的状况：_________(包括赠与标的的名称、数量、所在地等);

2.赠与方的权利：_________;

3.赠与方的责任义务：_________;

4.赠与物交付的时间、地点：_________。

5.乙方应于_________之间做出是否接受赠与的意思表示，否则，赠与不发生效力。

6.其它_________。

甲方(盖章)：_________ 乙方(盖章)：_________

地址：_________ 地址：_________

电话：_________ 电话：_________

法定代表人或负责人(签字)：_________ 法定代表人或负责人(签字)：_________

_________年____月____日 _________年____月____日

企业策划合同范本

委托方（甲方）：_________

顾问方（乙方）：_________

一、企业策划合同是指当事人一方为另一方就公司提供可行性论证、技术预测、专题技术调查、分析评价报告、_________所订立的合同。

二、技术情报和资料的保密

包括当事人各方情报和资料保密义务的内容、期限和泄漏技术秘密应承担的责任。

三、本合同变更、解除、终止必须由双方协商一致，并以书面形式确定。

四、本合同依据《中华人民共和国合同法》的规定，合同双方就_________公司的企业策划，经协商一致，签订本合同。

五、咨询的内容、形式和要求：乙方为甲方提供宣传方案并进行实施

六、履行期限、地点和方式

本合同自_______年___月____日至______年___月____日在_______（地点）履行。

本合同的履行方式：提交策划方案后，甲方认可后付款。

七、报酬及其支付方式

（一）本项目报酬（咨询经费）：_________元。

（二）支付方式（采用以下第_________种方式）：

1、一次支付：_________元，时间：_________

2、分期支付：_________元，时间：_________；_________元，时间：_________

3、其他方式：_________

八、违约金或者损失赔偿额的计算法

违反本合同约定，违约方应当按合同法规定，承担违约责任。_________。

九、补充与附件

本合同一式两份，双方各执一份。合同未尽事宜，经甲、乙双方协商决定需要补充或修改的，书写《合同修改意见书》一式两份（经甲、乙盖章签字，各存一份），做为本合同的补充件。本合同的附件和补充合同均为本合同不可分割的组成部分，与本合同具有同等的法律效力。

十、争议的解决办法

（一）本合同受中华人民共和国法律管辖并按其进行解释。

（二）本合同在履行过程中发生的争议，由双方当事人协商解决，也可由有关部门调解；协商或调解不成的，按下列第_________种方式解决：

1、提交_________仲裁委员会仲裁；

2、依法向人民法院起诉。

十一、本合同有效期限：_______年___月__日至______年____月____日

甲方（盖章）：_________??? 乙方（盖章）：_________???????

法人代表：_________ 法人代表：_________

联系地址：_________ 联系地址：_________

电话：_________ 电话：_________

_______年___月___日 _______年___月___日

签订地点：_________ 签订地点：_________

济南市应对金融危机困难企业缓缴和补缴社会保险费协议

甲方：

乙方：

根据人力资源和社会保障部等三部门《关于采取积极措施减轻企业负担稳定就业局势有关问题的通知》，及山东省《关于减轻企业负担稳定就业局势有关问题的通知》（鲁劳社[]7号、济南市《关于减轻企业负担稳定就业局势有关问题的通知》（济劳社字[]8号）规定，对经济南市劳动保障局会同财政局认定并经批准缓缴社会保险费的困难企业，就缓缴和补缴社会保险费的有关事宜与甲方达成如下协议：

一、甲乙双方必须认真贯彻执行鲁劳社[]7号、济劳社字[]8号规定，履行社会保险费缓缴的责任和义务。

二、乙方因经营困难，申请缓缴XX年____月至____月社会保险费_____个月。

三、乙方应于________年____月____日前一次性补缴齐缓缴的社会保险费，甲方不计收滞纳金。逾期按《社会保险费征缴暂行条例》规定处理。

四、缓缴社会保险费期间，乙方应继续按月申报应缴纳社会保险费，并积极筹措资金补缴社会保险费。在缓缴期内，如发生职工达到法定退休年龄等原因需要办理减员时，应办理个案补缴。_______年____月____日前办理减员个案补缴的，补缴缓缴期内及缓缴期前所欠社会保险费时养老保险不加系数、其它险种不再加收滞纳金。

五、甲方在乙方补缴缓缴的社会保险费后，应连续计算企业和职工的缴费年限。

六、甲方要求乙方提供必要的担保或抵押的，超过缓缴期限（遇法律明确的不可抗力除外）乙方拒不缴纳社会保险费的，甲方可通过劳动监察部门或法律程序申请人民法院强制执行，处置担保或抵押财物。

七、本协议自双方签字盖章之日起生效，一式三份，甲、乙双方各一份，报同级劳动保障部门备案一份。

甲方单位（章）： 乙方单位（章）：

甲方法人代表： 乙方法人代表：

年 月 日 年 月 日

出让方(甲方)：_______________

证照号码：___________________

法人代表：___________________

受让方(乙方)：_______________

证照号码：___________________

法人代表：___________________

中介方：_____________________

地址：_________电话：________

根据中华人民共和国有关法律、法规和本市有关规定，甲、乙双方遵循自愿、公平和诚实信用的原则，经协商一致订立本合同，以资共同遵守。

第一条 甲方将位于________有限公司自有产权的工业厂房及附属设施、国有土地使用权转让给乙方。该标的具体情况如下：

1，国有出让工业用地面积：________平米，土地证号：________号。终止日期：________年________月________日。

2，已建厂房及附属用房，建筑面积合计________平米。房产证号：________房权证________区字第________号。

3，水电及消防、排污设施、固定装饰装潢，照明设备。

第二条甲方确保上述标的产权清晰，所有权明确，无权益纠纷，无抵押贷款，本次交易甲方已征得权利共有人及隐性权利人的同意;乙方现场查看过上述标的，对于该标的所处位置、建筑及设施情况、以及交易税费情况充分了解，自愿买受该标的。

第三条甲、乙双方经协商一致，同意上述标的整体出让价款为人民币________万元(大写：________)。办理房产土地交易过户手续，交易税费按照法律规定各自承担。

(一)甲乙双方在中介方的见证下于________年________月________日签定本合同，同时乙方支付定金人民币________万元给甲方。

(二)本合同签定后，双方办理国有土地使用权转让鉴证手续，甲乙双方根据国土部门的要求提供相关材料。国有土地使用权转让鉴证手续完成，乙方支付第二笔出让价款人民币________万元(大写：________万元人民币)给甲方。

(三)国有土地使用权转让鉴证手续完成后，双方办理房屋产权交易手续，________房屋产权交易手续完成后，乙方支付第三笔出让价款人民币________万元(大写：________万元人民币)给甲方。

(四)上述全部交易手续完成一周内，双方办理标的移交手续。甲方结清该标的移交之前所产生的所有水电汽及其他费用后，将上述标的移交给乙方，乙方支付余款人民币________万元(大写：________万元人民币)给甲方。自移交一日起该厂房土地的租赁权移交乙方，租金由乙方收取。

第四条甲、乙双方确认，本合同签订后，除房地产交易管理部门依法作出不予过户决定外，上述标的权利转移日期以房地产交易管理部门受理该标的转让过户申请之日为准。双方承诺，对于办理过户手续积极给予协助。由于任何一方故意拖延或者不及时提供相关材料的，造成对方损失的，违约方负责赔偿。

第五条 乙方未按本合同约定期限付款的，甲、乙双方同意按下列_______款内容处理。

(一)每逾期一日，乙方应向甲方支付逾期未付款千分之五的违约金，合同继续履行。

(二)甲方书面催告乙方之日起的30日内，乙方仍未付款的，甲方有权单方解除合同。违约责任由乙方承担，造成甲方损失的，乙方负责赔偿。

第六条 甲方未按本合同约定的期限将上述标的交付给乙方，甲、乙双方同意按下列第____款内容处理。

(一)每逾期一日，甲方应向乙方支付已收款千分之五的违约金，合同继续履行。

(二) 乙方书面催告甲方之日起的30日内，甲方仍未交付上述标的的，乙方有权单方解除合同，违约责任由甲方承担，造成乙方损失的，甲方负责赔偿。

第七条本合同签定后，若甲乙任何一方以任何理由反悔的，或因违约而造成合同无法履行的，需向对方赔偿违约金人民币________万元，并赔偿对方经济损失，同时承担双方全部中介费用。

第八条 本次交易过户手续由甲方负责办理，中介方协助。所需材料由甲乙双方提供，办理过户过程中需要交纳的税费按照法律规定由甲乙双方各自承担。

第九条本次交易甲方需支付中介费________万元，乙方支付中介费________万元。本合同签订当日，甲乙双方各支付50%中介费;房屋产权交易手续完成后，甲乙双方移交标的当日，各支付余下的50%中介费。

第十条 经甲、乙双方协商一致，双方签定的补充协议，为买卖合同不可分割的一部分。本合同补充条款与正文条款不一致的，以补充条款为准。

第十一条 本合同自三方签订之日起生效。

第十二条本合同适用中华人民共和国法律、法规。甲、乙双方在履行本合同过程中若发生争议，应协商解决，协商不能解决的，可依法向________人民法院起诉。

甲方(公章)：________________乙方(公章)：________________

法定代表人(签字)：__________法定代表人(签字)：__________

_________年____月____日 _________年____月____日

技术出口合同范本

Contract for Equipment Sales and Technology Licensing

Contract No. ____________________

This Contract (hereinafter referred to as the “Contract”) is made and entered into as of ________ (the date of signature ) in ________ (the place of signature) through friendly negotiation by and between _____________, a company incorporated and existing under the laws of ____________ with its registered address at ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­_________________________________, and with its principal place of business at _________________________________ (hereinafter referred to as the “Buyer”), and ____________________, a company incorporated and existing under the laws of the People’s Republic of China with its registered address at ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­_________________________________, and with its principal place of business at _________________________________(hereinafter referred to as the “Seller”).

Whereas, the Buyer desires to engage the Seller to provide the Equipment, related design, Technical Documentation, Technical Service and Technical Training and to obtain from the Seller a license of Patent and/or Know-how in relation to the Erection, Test Run, Commissioning, Performance Test，operation and maintenance for the Equipment, as well as manufacture of the Contract Products. Now it is hereby mutually agreed as follows:

Article 1 Definitions

1.1 “Acceptance ”means the Buyer accepted the Equipment in accordance with Article 11.5.

1.2 “Commissioning” means the operation of the Equipment in accordance with Article 11.4 for the purpose of carrying out Performance Test.

1.3 “Contract” means this Contract signed by and between the Buyer and the Seller, including Appendices attached which shall form an integral part of this Contract.

1.4 “Contract Products” refers to all types of the products manufactured with Patent and/or Know-how under the Contract, details of which are specified in Appendix 1.

1.5 “Destination Airport” refers to _____________Airport.

1.6 “Effective Date of the Contract” means the date when the Contract enters into force upon fulfillment of all the conditions stated in Article 18.1.

1.7 “Equipment” means the equipment, machinery, instruments, spare parts and materials supplied by the Seller as listed in Appendix 3.

1.8 “Erection” means placing the Equipment to the positions according to the design drawings, and connecting it with relevant equipment and utilities.

1.9 “Improvement” refers to new findings and/or modifications made in the validity period of the Contract by either party on Patent and/or Know-how in the form of new designs, formulas, recipes, ingredients, indices, parameters, calculations, or any other indicators.

1.10 “Job Site” means the site where the Equipment shall be located and/or erected, namely ____.

1.11 “Know-how” refers to any valuable technical knowledge, data, indices, drawings, designs and other technical information, concerning the Erection, Test Run, Commissioning, Performance Test，operation and maintenance for the Equipment as well as manufacture of the Contract Products, developed and owned or legally acquired and possessed by the Seller and disclosed to the Buyer by the Seller, which is unknown to either public or the Buyer before the Date of Effectiveness of this Contract, and for which appropriate protection measures have been taken by the Seller for keeping Know-how in secrecy. The specific description of Know-how is set forth in Appendix 3.

1.12 “Last Shipment” means the shipment with which the accumulated invoice value of shipped goods has reached ____ ( ) percent of the total Equipment price.

1.13 “Patent” refers to any and all of the effective patent rights possessed by the Seller and licensed to the Buyer under the Contract in connection with the Erection, Test Run, Commissioning, Performance Test,operation and maintenance for the Equipment, as well as manufacture of the Contract Products, the No. and list of which are set forth in Appendix 3.

1.14 “Performance Test” means the tests for examining whether the Equipment is able to meet guarantee figures specified in Appendix 1.

1.15 “Technical Documentation” means the technical indices and data, specifications, drawings, processes, technical and quality standards, and other documents carrying the descriptions and explanations of Patent, Know-how and other technical information, in connection with the Erection, Test Run, Commissioning, Performance Test，operation and maintenance for the Equipment, as well as manufacture of the Contract Products, to be provided by the Seller as listed in Appendix 4.

1.16 “Technical Service” means the technical instruction, assistance and guidance rendered by the Seller as per Appendix 6.

1.17 “Technical Training ” means the training rendered by the Seller as per Appendix 7.

1.18 “Test Run” means the initial run of a single machine or the whole system of the Equipment without materials.

1.19 “Warranty Period” means the period of the warranty given by the Seller as specified in Article 12.2, during which the Seller is responsible for the defects of the Equipment as per Article 12.

Article 2 Scope of the Contract

2.1 The Seller’s Obligation

2.1.1 The Seller shall supply the Equipment, provide the design, Technical Documentation, and conduct the Technical Service and Technical Training, and grant the Buyer a right to use the Patent and/or Know-how as set forth in the Contract.

2.1.2 The Seller shall supply the Equipment which is listed in Appendix 3, the specification is detailed in Appendix 1.

2.1.3 The Seller shall provide design in accordance with Appendix 5, and submit to the Buyer the Technical Documentation listed in Appendix 4.

2.1.4 The Seller shall conduct the Technical Services at the Job Site as per Appendix 6.

2.1.5 The Seller shall conduct the Technical Training as per Appendix 7.

2.2 The Buyer’s Obligation

2.2.1 The Buyer shall at his own costs and expenses, provide the Seller with all information and data concerning the design as per Appendix 2. The Buyer shall ensure the completeness, correctness and accuracy of all such information and data.

2.2.2 The Buyer shall at his own costs and expenses, obtain all necessary import permits, undertake customs clearance, take delivery of the Equipment to be supplied by the Seller and transport them to the Job Site in time.

2.2.3 The Buyer shall at his own costs and expenses, perform all the civil works, construction, Erection, Test Run， Commissioning and Performance Test in accordance with the Technical Documentation under the Technical Services rendered by the Seller as per Appendix 6.

2.2.4 The Buyer shall at his own costs and expenses, supply all the equipments, spare parts and facilities required, except for the Equipment supplied by the Seller as per Appendix 3.

2.2.5 The Buyer shall at his own costs and expenses, provide the qualified and appropriate technical personnel, labor, tools, utilities and the Job Site in time for Erection, Test Run, Commissioning, and Performance Test as specified in Appendix 2.

2.2.6 The Buyer shall at his own costs and expenses, perform necessary administration and security guard at the Job Site.

Article 3 Grant of License

3.1 The Seller agrees to grant to the Buyer and the Buyer agrees to obtain from the Seller a license to manufacture the Contract Products as well as to conduct Erection, Test Run, Commissioning, Performance Test, operation and maintenance for the Equipment with Patent and/or Know-how as well as to use and sell the Contract Products. The name, model, specification, and technical data of the Contract Products are detailed in Appendix 1. The Buyer shall not make use of Patent and/or Know-how for any purposes other than those stipulated in the Contract without prior written approval from the Seller. The annual output of the Contract Products manufactured by the Buyer shall in no case exceed _______________.

3.2 (Option 1) The license granted under the Contract shall be an exclusive license. The Seller shall not retain its right to grant the licenses to any third parties, or to explore Patent and/or Know-how as well as to sell the Contract Products by itself within the territory specified in Article 3.4.

(Option 2) The license granted under the Contract shall be a non-exclusive license. The Seller shall retain its right to grant the licenses to any third parties, and to explore Patent and/or Know-how as well as to sell the Contract Products by itself within the territory specified in Article 3.4.

3.3 The license granted under the Contract shall be a non-transferable and non-sublicensing license, under which the Buyer shall neither be entitled to transfer nor grant sub-license to any third party without prior written approval from the Seller.

3.4 Territory

3.4.1 The Seller agrees to grant the license to the Buyer only within the territory of _________________ (country or region). The Buyer shall not explore Patent and/or Know-how in any place other than the Job Site without previous written consent of the Seller.

3.4.2 The Seller agrees to grant a license to the Buyer to use and sell the Contract Products only within the territory of ________________________ (Country or region). In case the Buyer fails to perform its obligations under this Clause, all the actual losses and damages thus incurred to the Seller shall be borne by the Buyer, and the Seller shall have the right to terminate the Contract without prejudice to any remedies specified in the Contract.

Article 4 Price

4.1 The Buyer agrees to pay the total Contract price, Technical Training and Technical Service fee to the Seller.

4.2 The total Contract price, including price of the Equipment, design, Technical Documentation and a license fee in a fixed amount, shall be __________(say _______________________ only).

The breakdown price is as follows:

The price for Equipment is __________(say _______________________ only).

Fee for design is __________(say _______________________ only).

Fee for Technical Documentations is __________(say _______________________ only).

License fee is __________________(Say: _________________ only)

4.2.1 The total Contract price for the Equipment is for delivery CIF_____ Port, and the Technical Documentations is for delivery CIP (by air) ______ Airport. CIF and CIP term shall be interpreted in accordance with INCOTERMS 2019, issued by the INTERNATIONAL CHAMBER OF COMMERCE (ICC).

4.2.2 The total Contract price includes the price for spare parts listed in Appendix 3. However, the total Contract price does not cover the supply of any other spare parts. At the Buyer’s request, the Seller may provide with any other spare parts. A separate agreement shall be signed between the parties.

4.2.3 The above price is fixed and firm.

4.3 The total Contract price does not cover the Technical Service fee and Technical Training fee specified in Appendix 6,7.

4.4 The total Contract price as well as the Technical Training and Technical Service fee shall not be regarded or in any way be explained or interpreted as covering any of the custom duties, taxes, or charges, fees, and expenses unless expressly listed in the Contract.

Article 5 Payment

5.1 Down Payment

Within ____ ( ) days after signing the Contract, the Buyer shall pay ____ ( ) percent of the total Contract price amounting ____ by T/T to the Seller.

5.2 [Option One: Payment by Sight L/C]

The balance of the total Contract price amounting ___ ( says ___ only ) shall be paid by an irrevocable Letter of Credit at sight, issued within ___ ( ) days after signing the Contract by a reputable bank in ___ acceptable to the Seller in favor of the Seller. The Letter of Credit shall be available upon the presentation of the following documents till ______(specific expiration date or a specific circumstance for the expiration of the Letter of Credit).

5.2.1 ____ ( ) percent of the total Contract price amounting ____ (say ___ only) shall be paid by the Buyer to the Seller within _______ days after the following documents have been submitted by the Seller:

(a) Bill of Lading in one (1) original and ___ ( ) copies;

(b) Commercial Invoice in one (1) original and ___ ( ) copies;

(c) Packing list in one (1) original and ___ ( ) copies;

(d) Certificate of Origin in one (1) original and ___ ( ) copies;

(e) Insurance Policy in one (1) original and ___ ( ) copies;

5.2.2 ____ ( ) percent of the total Contract price amounting ____ (say ___ only) shall be paid by the Buyer to the Seller within _______ days after the following documents have been submitted by the Seller:

(a) One (1) copy of the Acceptance Certificate signed by the Buyer as per Article 11.5, or the Seller’s written statement specifying the lapse of more than seven (7) days after the Seller’s notice requesting the Buyer to issue the Acceptance Certificate in accordance with Article 11.5;

(b)One ( 1 ) copy of commercial invoice.

5.2.3 ____ ( ) percent of the total Contract price amounting ____ (say ___ only) shall be paid by the Buyer to the Seller within _______ days after the following documents have been submitted by the Seller:

a) One (1) original Letter of Retention Guarantee in the form of Appendix 10;

b) One (1) copy of Commercial Invoice.

5.2 [Option Two: Payment under a L/G]

The balance of the total Contract price amounting ___ (say ___ only ), plus interest for deferred payment in the amount of ___ (say ___ only ), totaling ___ (say ___ only ) as detailed in Appendix 12 shall be paid by the Buyer by installments as specified in Appendix 12 and backed by an irrevocable Letter of Guarantee in favor of the Seller as per the Appendix 11, issued within ___ ( ) days after signing the Contract by the reputable bank in ____ acceptable to the Seller.

5.3 All the banking charges incurred in the Seller’s bank shall be borne by the Seller while those incurred outside the Seller’s bank shall be borne by the Buyer.

Article 6 Delivery of Equipment and Technical Documentation

6.1 The Delivery of the Equipment

6.1.1 The delivery of the Equipment listed in Appendix 3 shall be completed within ____ ( ) months from the Effective Date of the Contract.

6.1.2 Within ____ ( ) months after the Effective Date of the Contract, the Seller shall send to the Buyer a preliminary delivery schedule by fax.

Not later than ____ ( ) days before the first shipment, the Seller shall submit to the Buyer the final delivery schedule in three (3) copies indicating Contract number, dispatch number, name of the Equipment, quantity, approximate dimensions, volume of each package and time of each shipment.

6.1.3 The port of shipment is ____, while the port of destination is ____.

6.1.4 Advance shipment, partial shipment and transshipment are allowed, however, the Seller shall inform the Buyer thirty (30) days before such shipment.

6.1.5 The date of Bill of Lading for each shipment shall be considered as the actual delivery date.

6.1.6 The Seller shall notify the Buyer by fax of the following within five (5) working days after each shipment is effected:

(a) Contract number

(b) Name of the vessel and loading port

(c) Name of the Equipment shipped

(d) Number and date of Bill of Lading

(e) Total volume

(f) Total gross and net weight

(g) Total number of packages/cases

6.1.7 The Seller shall airmail the following documents in duplicate to the Buyer:

(a) Bill of Lading

(b) Commercial Invoice

(c) Packing List

(d) Certificate of Origin

(e) Insurance Policy.

6.2 The Late Delivery of the Equipment

6.2.1 If the Seller fails to deliver the Equipment in accordance with the final delivery schedule, the Seller shall pay to the Buyer liquidated damages for such delay at the following rates:

(a) From the first week to the fourth week, the liquidated damages shall be

____ ( ) percent of the value of the delayed portion of the Equipment per

week

(b) From the fifth week to the eighth week, the liquidated damages shall be

____ ( ) percent of the value of the delayed portion of the Equipment per week

(c) From the ninth week, the liquidated damages shall be ____ ( ) percent of

the value of the delayed portion of the Equipment per week

6.2.2 The fractions of four days or more shall be counted as one week and fractions of less than four days shall be omitted. The total aggregate amount of the liquidated damages shall not exceed ____ ( ) percent of the value of the delayed portion Equipment.

6.2.3 The Seller shall be released from the liability to the Buyer whatsoever in respect of the late delivery after his payment of liquidated damages in accordance with Article 6.2. Notwithstanding the Seller’s payment of the liquidated damages for the late delivery Equipment, the Seller shall not be released from his obligation to deliver the Equipment.

6.3 The Delivery of the Technical Documentation

6.3.1 The Technical Documentation listed in Appendix 4 shall be delivered CIP ____airport by air within ____ ( ) months after the Effective Date of the Contract.

6.3.2 The date of airway bill shall be regarded as the actual delivery date of the Technical Documentation.

6.3.3 Within ____ ( ) working days after sending each lot of the Technical Documentation, the Seller shall inform the Buyer of the Contract number, item number, number and date of airway bill and the flight.

6.3.4 In case of shortage, loss of or damage to the Technical Documentation due to the Seller’s reason, the Seller shall make supplement to the Buyer within ____ ( ) days after receiving the Buyer’s written notification without any further charge.

Article 7 Packing and Marking

7.1 The Equipment shall be packed to withstand long distance transportation, multiple handling.

7.2 The Seller shall mark the following on two opposite sides of each package with indelible painted English words:

(a) Destination

(b) Consignee

(c) Contract number

(d) Shipping mark

(e) Gross/net weight (kg)

(f) Case/ bale number

(g) Dimensions: L x W x H (cm)

7.3 Each package shall contain one (1) copy of packing list.

7.4 The Seller shall mark on the package, if necessary, “Handle with Care", “Right Side Up", “Fragile" or other indicative marks according to the characteristics and feature of the goods as well as different requirement for transportation, loading and unloading of the goods.

7.5 If the goods weigh three (3) or more than three (3) metric tons, gravity, hoisting position and illustrative marks shall be marked so as to facilitate loading, unloading and handing.

(a) Destination

(b) Consignee

(c) Contract number

(d) Gross/net weight (kg)

(e) Item number

(f) Dimensions: L x W x H (cm)

Article 8 Technical Service and Technical Training

8.1 The Seller shall dispatch technical personnel to Job Site to render Technical Service in accordance with Contract according to a time schedule agreed upon between both parties. The number, specialty, rank, treatment of the personnel, and payment as well as the contents, and requirements of Technical Service are specified in Appendix 6.

8.2 The Buyer shall have the right to send its technical personnel to the relevant factory selected by the Seller for training. The number, speciality, treatment of the personnel, and payment as well as the contents, time schedule, and requirement of training, are specified in Appendix 7.

8.3 Either party shall provide assistance to the other party’s technical personnel in their application for visa, working permit, and/or other necessary formalities for rendering Technical Service or training under the Contract in the other party’s factory.

8.4 Either Party’s technical personnel shall abide by the laws of the other party’s country and the regulations of the other party during their stay in the other party’s country.

Article 9 Standards and Inspection

9.1 The Seller shall carry out the design, manufacture, inspection and test of the Equipment according to the existing standards of the People’s Republic of China, namely GB.

9.2 The Seller or the manufacturer shall, at his own costs and expenses, inspect the Equipment and issue the ex-work quality certificate.

9.3 The open-case inspection of the Equipment shall be performed by the Buyer in the presence of the Seller’s representatives on the Job Site in days after the arrival of the Equipment at the Job Site. The open-case inspection fee shall be borne by the Buyer.

The Buyer shall inform the Seller of the date one (1) month before the date of open case inspection and shall also render assistance to the Seller’s representatives in their inspection work.

9.4 During the joint open-case inspection, a detailed inspection record shall be made and signed by the representatives of both parties.

In case the Seller is responsible for any defect or shortage of the Equipment, the inspection record shall be taken as an effective evidence for the Buyer to claim repair, replacement or supplement to the Seller. Any of such claims shall be lodged by the Buyer within month(s) after the arrival of the Equipment at the Job Site.

9.5 If any shortage, defect of or damage to the Equipment is found in open-case inspection not attributable to the Seller’s responsibility, the Seller shall make repair, replacement or supplement at the Buyer’s expenses in accordance with the separate agreement signed by both parties.

9.6 The Buyer is not entitled to open the case, assemble and/or disassemble the Equipment without the Seller’s prior written consent.

If there is no joint open case inspection due to the reasons not attributable to the Seller, the quantity and apparent quality of the Equipment shall be deemed correct and in perfect condition.

Article 10 Design and Design Liaison

10.1 The Buyer shall provide to the Seller within ____ ( ) days after the Effective Date of the Contract, all the design data which shall be taken as the design basis. The Seller shall not be liable to the Buyer for, and the Buyer shall indemnify the Seller and hold the Seller harmless from any damages or failure caused by the incompleteness, incorrectness and/or inaccuracy of any such information and data.

10.2 A design liaison meeting shall be held in the ____ ( ) month after receiving above mentioned design data, the Seller will dispatch his technical personnel to the Job Site to participate in the meeting. During the meeting period, the Seller will discuss with the Buyer the relevant design details. Both parties shall sign an agreement outlining the design details.

10.3 During the design liaison meeting, the Seller and the Buyer shall provide assistance to the other’s dispatched personnel in arranging entry visas to the respective countries. The expense incurred on the dispatched personnel shall be borne by the party respectively.

Article 11 Erection, Test Run, Commissioning, Performance Test and Acceptance

11.1 The Erection, Test Run, Commissioning, Performance Test shall be conducted by the Buyer.

11.2 Chief Representatives

11.2.1 Each party shall nominate one (1) Chief Representative to deal with the technical matters during the period from the start of the Erection to Acceptance of the Equipment.

11.2.2 Detailed arrangements shall be made through friendly discussions by the Chief Representatives of both parties. The Chief Representatives of both parties shall fully cooperate to carry out their duties stipulated in the Contract, however they have no right to revise, alter or amend the Contract without the written authorization of both parties.

11.2.3 The Chief Representatives of both parties shall communicate through Linking Sheet for the matters relative to opinions, suggestions and information. The linking sheet shall be countersigned by the other party.

11.3 Erection and Test Run

11.3.1 The Erection shall be completed by the Buyer in ____ ( ) days from the effective date of the Contract. The Seller’s Chief Representative shall arrive at the Job Site ____ ( ) days prior to the beginning of the Erection.

11.3.2 When Erection is completed and in full conformity with requirements of the Technical Documentation, a Certificate of Completion for Erection of the Equipment shall be signed by the Chief Representatives of both parties in two (2) originals, one for each party, within three (3) days. The date of signing said Certificate shall be deemed as the date of completion of Erection.

11.3.3 As soon as the completion of Erection, Test Run for single machine and the whole system of the Equipment shall be started.

11.3.4 When Test Run has been successfully performed, a Certificate of Completion for Test Run of the Equipment shall be signed by the Chief Representatives of both parties in two (2) originals, one for each party, within three (3) days. The date of signing the said Certificates shall be deemed as the date of completion of Test Run of the Equipment.

11.4 Commissioning and Performance Test

11.4.1 Within ____ ( ) days after the completion of the Test Run, the Buyer shall make available qualified operation and maintenance personnel, raw materials, spare parts, utilities and other matters required for the Commissioning. Detailed procedures such as instrument calibrating, items of recording, sampling methods and analyzing methods, which are necessary for the Commissioning shall be discussed and agreed upon by the Chief Representatives of both parties.

If in the opinion of both parties, the Equipment is ready for the Commissioning, both parties shall confirm the readiness for the Commissioning in writing.

11.4.2 The Commissioning of the Equipment shall be started immediately after the confirmation of the readiness for the Commissioning. The Commissioning period shall ____ ( ) days after commencement of the Commissioning.

11.4.3 When the Seller and the Buyer consider that stable operation of the Equipment has been achieved, the date of Performance Test shall be fixed by Chief Representatives of both parties.

11.4.4 The Seller shall have the right to access to the laboratory and testing facilities in order to take samples and make analytical tests. The sample taking and analytical test during the Commissioning period will be done in the presence of the Chief Representatives of both parties.

11.4.5 During the period of Commissioning until Acceptance of the Equipment, the Seller may use the Buyer’s stored spare parts. Should the Buyer’s stored spare parts be used by the Seller due to the Seller’s responsibility, the Seller shall replenish the stores with the same in time at Job Site; otherwise the Seller shall provide the same at the Buyer’s costs upon the Buyer’s timely request.

11.4.6 If the result of Performance Test has reached the guarantee figures as per Appendix 1, the Acceptance Certificate of the Equipment shall be signed by the Chief Representatives of both parties in two (2) originals, one for each party, within three (3) days.

11.4.7 If the Performance Test cannot meet guarantee figures specified in Appendix 1, both parties shall jointly make investigations so as to find out the reason for clarifying the responsibility.

11.4.8 If the guarantee figures are not met due to the Seller’s reason, the Buyer shall agree to give an extension of ____ ( ) months so that the Seller can make improvement or adjustment to the Equipment and conduct further Performance Test. All the costs and expenses for making improvement or adjustment to the Equipment shall be borne by the Seller.

11.4.9 During the extension period, if the guarantee figures are still not met due to the Seller’s reason, the Seller shall pay the liquidated damages as per Appendix 1 to the Buyer against the Acceptance Certificate signed by both parties.

The Seller’s aggregate liability to pay liquidated damages for failure to attain the performance guarantees shall not exceed ____ ( ) percent of the Equipment price. The Seller shall have no further liability whatsoever to the Buyer in respect of such failure after payment of the liquidated damages.

11.4.10 If the non-achievement of the guarantee figures is due to the reasons not attributable to the Seller, the Seller shall agree to give an extension of ____ ( ) months. During the extension period all costs thereto incurred for the adjustment of the Equipment, as well as the costs and expenses for the Seller’s technical personnel shall be borne by the Buyer. In case the guarantee figures still can not be achieved due to the reasons not attributable to the Seller in the extension period, the Equipment shall be accepted by the Buyer. Both parties shall sign the Acceptance Certificate.

11.5 Acceptance

11.5.1 Acceptance shall occur in respect of the Equipment when :

(a) Performance Test has been successfully completed as per the Article 11.4.6.; or

(b) The Performance Test has not been completed due to the reasons not attributable to the Seller such as delayed civil construction, lack of and/or any other inconformity of raw materials, spare parts of the Buyer’s scope of supply under Appendix 2, and utilities with the requirements of the Contract in the ____ ( ) months from the date of Bill of Lading of the Last Shipment; or

(c) The Seller has paid the liquidated damages as per Article 11.4.9; or

(d) The guarantee figures still can not be reached due to reasons not attributable to the Seller’s reason in the extension period as specified in Article 11.4.10; or

(e) The Buyer takes the single machine and the whole system of the Equipment into use without the Seller’s approval.

11.5.2 At any time after any of the events set out in Article 11.5.1 has occurred, the Seller may give a notice to the Buyer requesting the issuance of the Acceptance Certificate.

11.5.3 The Buyer shall within seven (7) days after receipt of the Seller’s notice, issue such Acceptance Certificate.

11.5.4 If within seven (7) days after receipt of the Seller’s notice, the Buyer fails to issue the Acceptance Certificate or fails to inform the Seller in writing, with convincing evidence, of the reason why the Buyer has not issued the Acceptance Certificate, the Equipment shall be deemed having been accepted on the seventh day of the Seller’s said notice.

11.5.5 After the Acceptance, the Seller’s responsibilities and obligations under the Contract shall be deemed having been fulfilled except those as stipulated in Article 12 and 14.

Article 12 Guarantee and Warranty

12.1 The Seller guarantees that:

(a) The Equipment supplied by the Seller shall be new and made of adequate materials, and in conformity with the technical requirements of the Contract;

(b) The Technical Documentation shall be complete, clear and correct.

12.2 The period of warranty given by the Seller under Article 12.1 shall be ____ ( ) months from the date of Acceptance or ____ ( ) months from the date of Last Shipment, whichever comes earlier.

12.3 Defect of the Equipment

12.3.1 During the Warranty Period, should any defect due to inferior materials or bad workmanship of the Equipment be found under normal operation, the Buyer shall give the Seller a notice stating the details, together with all available evidence.

The Seller shall take immediate action to eliminate the defect at the Seller’s expenses within the period agreed by both parties.

12.3.2 If certain defect can not be eliminated despite of several attempts, the Seller shall replace the defective parts with non-defective parts at the Seller’s costs and expenses.

12.3.3 If the defect is eliminated by the Buyer himself, subject to the Seller’s prior written consent, all the direct costs and expenses thus incurred shall be borne by the Seller.

12.3.4 The Seller may reduce the price of the defective Equipment according to the degree of inferiority or extent of damage as agreed by both parties. After the reduction the Seller shall be released from its obligations and liabilities.

12.3.5 During the Warranty Period, should any defect due to the Buyer’s improper operation or maintenance be found, the Seller will provide technical assistance to eliminate the defect or replace the defected parts upon Buyer’s requests. All the costs and expenses thus occurred shall be borne by the Buyer.

12.3.6 Subject to Article 12.3.1, The Seller shall not be responsible for any defect or damage to the Equipment arising out of any circumstances including but not limited to the following causes:

(a) Combination of the Equipment with any machinery, and/or component other than those supplied by the Seller; or

(b) Alteration, modification or repair without the Seller’s prior written consent; or

(c) Failure of the Buyer to follow the Technical Documentation and instructions of the Seller, including the Buyer’s improper operation and maintenance; or

(d) Normal wear and tear.

12.4 During the Warranty Period, should the Technical Documentation supplied by the Seller be found incomplete, unclear or incorrect due to the Seller’s reason, the Seller shall be liable to supplement, replace or correct the Technical Documentation free of charge.

12.5 The Seller shall in no respect be understood or interpreted as liable for the commercial development of the Contract Products. The Buyer shall undertake the risk of the commercial development of the Contract Products.

12.6 In no circumstances, whether as a result of breach of contract, warranty, indemnity, tort (including negligence), strict liability, or otherwise, shall the Seller or its subcontractors or suppliers be liable for loss of profit or revenues, loss of production, loss of use, loss of information or data, cost of capital, cost of substitute equipment, facilities, services or replacement power, downtime costs, claims of the Buyer’s customers for such damages, or for any special, consequential, incidental, indirect or exemplary damages.

12.7 Notwithstanding anything to the contrary provided in the Contract, the aggregate liability of the Seller to the Buyer , on all claims of any kind, whether in contract, warranty, indemnity, tort (including negligence), strict liability, or otherwise, arising out of the performance or breach of the Contract or use of any Equipment or exploration of the Patent and/or Know-how shall not exceed ____ ( ) percent of the total Contract price.

12.8 All Contractual obligations of the Seller shall be deemed as having been fulfilled upon the expiry date of the Warranty Period.

Article 13 Intellectual Property Right

13.1 The Seller represents that it is entitled or authorized to grant the license to the Buyer to use the Patent and/or Know-how for the purpose as specified in Article 3.

13.2 The Buyer shall not use such Patent and/or know-how received from the Seller for any purpose other than that as specified in this Contract.

13.3 Any intellectual property right or other technical information granted by the Seller to the Buyer shall remain the property of the Seller. In no circumstances shall any terms and conditions in this Contract be construed, deemed, or interpreted as transfer of title to the Buyer of any information which may be delivered to or accessed by the Buyer.

13.4 Registration of the Contract and Maintenance of Patent

13.4.1 The Buyer shall, after the Contract is signed between both parties, make sure that the Contract is registered with or filed to the competent authorities in the Buyer’s country if it is required by law.

13.4.2 The Seller shall, during the validity period of the Contract, make all reasonable efforts to maintain Patent in force in the territory as stipulated in Article 3.4.1 and bear the costs thus incurred. The Buyer shall not make any action or inaction which may lead to invalidation or compulsory licensing of the Patent.

13.5 Improvement and Grant-back

13.5.1 Should any Improvement be made by the Seller on Patent and/or Know-how within the validity period of the Contract, which shall be the exclusive property of the Seller, the Seller shall grant the Buyer a non-exclusive license to exploit such Improvement at latest __________months from its improving, provided that the license fee is agreed upon between both parties.

13.5.2 The Buyer shall be entitled to make Improvement on Patent and/or Know-how within the validity period of the Contract. The Seller shall have the right to obtain and make use of the Improvement. The license fee shall be discussed between both parties in due time.

13.5.3 Both parties shall keep Improvement confidential. Neither party shall be entitled to grant any third party a sub-license on Improvement made and provided by the other party without previous written consent of the other party.

Article 14 Confidentiality

14.1 After signing of the Contract, both parties shall keep secret all the contents, terms, conditions of the Contract.

14.2 The Buyer shall take proper measures to keep strictly confidential of Know-how, Technical Documentation, Improvement and any other secret information obtained or accessible to from the Seller. The Buyer shall not disclose any of them to any third party, and shall not make use of them without prior written consent of the Seller except otherwise stipulated in the Contract.

14.3 The Buyer may disclose the secret information as described in Article 14.2 to the personnel of its own, or of any related parties engaged in the performance of the Contract subject to Article 14.2, strictly to the extent as essential for the implementation of the Contract, provided that the individuals and/or parties accessing or may access such secret information are engaged to undertake in written form the same confidential liability of the Buyer to the Seller. Any breach of confidentiality obligations by any personnel from the Buyer or the Buyer’s related parties shall be deemed as breach of the Contract by the Buyer.

14.4 Notwithstanding this Article 14, the Seller may furnish to its sub-contractor such documents, data, and other information received from the Buyer to the extent required for performing the Contract, in which event the Seller shall obtain from such sub-contractor an undertaking of confidentiality similar to that imposed on the Seller under the Article 14.

14.5 This Article 14 shall survive the expiration or termination of the Contract.

14.6 The confidential obligation shall not apply to the information which:

A. now or hereafter enters the public domain; or

B. can be proved to have been in the possession of the Party at the time of disclosure and which was not previously obtained, directly or indirectly, from the other Party hereto; or

C. otherwise lawfully becomes available to either party from a third party under no obligation of confidentiality.

Article 15 Taxes and Duties

15.1 All taxes and duties in connection with the signing and performance of the Contract, levied by Governments of the People’s Republic of China, including but not limited to customs duties, income tax, sales tax, value-added tax etc., shall be borne and paid by the Seller.

15.2. All taxes and duties in connection with the signing and performance of the Contract levied on the Buyer and Seller by the Buyer’s Governments, including but not limited to customs duties, income tax, sales tax, value-added tax etc., shall be borne and paid by the Buyer. The Buyer shall pay in due time and full amount and hold the Seller harmless from any taxes and duties in case incurred to the Seller in the signing and performance of the Contract.

15.3 All import taxes and duties for tools and/or instruments, which the Seller or the Seller’s personnel may bring to the Buyer’s country for the execution of the Contract, shall be borne and paid by the Buyer.

15.4 Any and all taxes and duties in connection with the signing and performance of the Contract levied in any place except the cases as specified in Article 15.1 are not included in the Contract price. Should the Seller make the relevant payment directly as the case may be, both Parties agree to amend the Contract price to fully compensate the Seller for the payment, and the Buyer shall fully refund the Seller for the relevant amount within_______( ) days from the Seller’s payment.

Article 16 Force Majeure

16.1 If either of the Contract parties is prevented from executing the Contract due to the event of Force Majeure such as war, riot, coup, embargo, flood, typhoon, tornado, snowstorm, earthquake and other events which could not be foreseen, avoided and overcome, the affected party shall notify the other party by fax within the shortest possible time of occurrences of the Force Majeure and send a certificate issued by competent authorities or agency certifying the event of the Force Majeure by registered or express mail within fourteen (14) days following its occurrence.

16.2 The affected party shall not be liable for any delay or failure in performing any of its obligations due to the event of Force Majeure. However the affected party shall inform the other party by fax the termination or elimination of the event of Force Majeure as soon as possible.

16.3 Both parties shall proceed with their obligations immediately upon the cease of the event of Force Majeure or the removal of the effects and the term of the Contract shall be extended correspondingly. Should the effect of the event of Force Majeure last for more than one hundred and twenty (120) days, either party shall have the right to terminate the Contract by a written notice.

Article 17 Applicable Law and Settlement of Disputes

17.1 The applicable law of the Contract shall be the laws of the People’s Republic of China.

17.2 All disputes arising from or in connection with the Contract shall be settled through friendly consultation between both parties. In case no agreement can be reached, the dispute shall be submitted for arbitration.

17.3 The arbitration shall be conducted by China International Economic and Trade Arbitration Commission (CIETAC) in Beijing in accordance with Arbitration Rules of the Commission in effect at the time of applying for arbitration. The tribunal shall be composed of three arbitrators.

17.4 The arbitral award shall be final and binding upon both parties.

17.5 During proceedings of arbitration, the undisputed part of the Contract shall be performed continuously by both parties regardless of such arbitration proceedings.

Article 18 Effectiveness, Term and Termination of the Contract

(a) The Seller and the Buyer sign the Contract;

(b) The Contract shall be approved by the competent authorities and/or banks of both parties (if applicable);

(c) The Seller receives the Down Payment;

(d) The Seller duly receives the L/C (or L/G ) issued by the Buyers Bank.

18.2 Each party shall use its best efforts to fulfill the above conditions for which it is responsible as soon as practicable.

18.3 If the Contract has not become effective pursuant to Article 18.1 within ____ ( ) months after the date of signing this Contract, the Seller has the right to make an equitable adjustment to the total Contract price and the time for delivery and/or other relevant conditions of the Contract. Should no agreement is reached for the above mentioned adjustment within ____ ( ) days from the Seller’s request of adjustment, the Seller shall be entitled to cancel the Contract.

18.4 The Contract shall be valid and remain in force for_____ (_____) years from the Date of Effectiveness, during which period the Buyer shall be entitled to manufacture the Contract Products with Patent and/or Know-how and sell the Contract Products within the licensed territory as specified in Article 3.4.

(Option 1) The Buyer shall not be entitled to manufacture with patent and/or know-how or sell the contract products after the aforesaid period unless the Buyer agrees to pay additional license fees in the amount and with the payment schedules and methods as agreed upon between both Parties in due time.

(Option 2) The Buyer shall be entitled to manufacture with Patent and/or Know-how or sell the Contract Products after expiration of the Contract term specified above, provided that the Buyer shall not be released from its confidential obligations under the Contract.

(Option 3) The Buyer shall not be entitled to manufacture with Patent and/or Know-how or sell the Contract Products after the expiration of the Contract term specified above, and shall return to the Seller all the Technical Documentations specified in Appendix 4 without remaining any duplicate copies. Nevertheless the confidential obligations of the Buyer under Article 14 shall survive the Contract term.

18.5 Either party may, without prejudice to any other remedy for the other party’s following breach of the Contract, terminate the Contract in whole or in part by a written notice send to the other party, if the other party

A. fails to perform its payment obligation under the Contract and does not remedy for its failure within a period of ______ (____) days upon receipt of the written notice or a period agreed upon between the parties; or

B. fails to perform its confidentiality obligation under the Contract; or

C. fails to perform any other obligations under the Contract except minor parts thereof, and does not remedy for its failure within a period of ______ (____) days upon receipt of the written notice or a period agreed upon between the parties; or

D. becomes bankrupt or insolvent, goes into liquidation, has a receiving or administration order made against him, compounds with his creditors, or carries on business under a receiver, trustee or manager for the benefit of his creditors, or dissolves, or ceases to do business, or be ordered to close down / to cease to do business / to dissolve, or has its business license revoked, or if any act is done or event occurs which (under applicable Laws) has a similar effect to any of these acts or events.

18.6 Either party may, without prejudice to any other remedy, terminate the Contract in whole or in part by a written notice send to the other party, if

A. The other party is prevented by the laws, statutes, rules or regulations of either country from performing its obligations under the Contract; or

B. The Seller is prevented by the relevant authority of the Buyer’s country from being paid in accordance with the Contract; or

C. The other party is prevented from performing its contractual obligations by any event of Force Majeure for more than one hundred and twenty (120) days.

18.7 In the event of termination of the Contract, without prejudice to any other remedies available according to the Contract and/or applicable laws,

The Buyer shall cease all its further exploitation of the Patent and/or Know-how and any acceptance of further orders from third parties for the Contract Products.

All the delivered literatures, drawings, samples, instruments, equipment, and other documents including the interpretations related to Patent and/or Know-how shall be returned to the Seller as the Seller’s requests.

All the contracts on sales of the Contract Products signed between the Buyer and third parties shall be terminated by the Buyer, otherwise the Seller shall be paid accordingly.

In case the termination is due to the Seller’s default, the Buyer shall be entitled to complete the performance of the contracts on sales of the Contract Products already signed between the Buyer and third parties before the termination.

The Seller shall be paid by the Buyer for all the contractual obligations performed by the Seller till the date of termination within _______days from receipt of the termination notice.

E. Termination of the Contract shall not release either party from its confidential obligations under the Contract

Article 19 Miscellaneous

19.1 The Contract is signed by the authorized representatives of both parties in ____ ( ) originals. Each party shall keep ____ ( ).

19.2 The Contract supersedes all communications, negotiations and agreements between the parties prior to the signing date of this Contract.

19.3 All amendments, supplements and alternations to terms of the Contract shall be made in written form and signed by the authorized representatives of both parties. These amendments, supplements and alternations shall form integral parts of the Contract.

If any costs occur or delivery delay due to amendment or explanation of the new law or statute or regulations enacted by the Buyer’s country after the effectiveness of the Contract，the Seller shall have the right to ask for necessary adjustment in relation to the Contract price and the delivery schedule.

19.4 No assignment, cession, novation, or transfer of any right or obligation under this Contract shall be made by either party to a third party without the prior written consent of the other party.

19.5 All communications between both parties in the course of implementation of the Contract should be in English language in written form at the address set forth below. The faxes concerning the important matters shall be confirmed in due time by registered or express mail or letter delivered by hand.

The Buyer:

Address:

Post Code:

Fax: __________________________

Tel.: __________________________

Email:__________________________

Attention: ______________________

The Seller :

Address:

Post Code:

Fax: __________________________

Tel.: __________________________

Email:__________________________

Attention: ______________________

IN WITNESS WHEREOF, the parties hereto have caused this Contract to be duly executed.

The Buyer:

The Seller:

By:______________________[Signature]

Name: [printed name]

By:_______________________ [Signature]

Name: [printed name]

Title:

Title:

Appendices

Appendix 1 Specifications and Guarantee Indices (Omitted)

非专利技术转让合同

非专利技术转让合同

转让方：＿＿＿＿＿＿＿＿＿

法定代表人或负责人：＿＿＿＿＿＿＿＿

受让方：＿＿＿＿＿＿＿＿＿＿

法定代表人或负责人：＿＿＿＿＿＿＿＿

根据《中华人民共和国合同法》的有关规定，经双方当事人协商一致，签订本合同。

1.项目名称：＿＿＿＿＿＿＿＿。

2.本非专利技术的性能，工业化开发程度：＿＿＿＿＿＿＿。

3.本合同的授权性质：＿＿＿＿＿＿＿＿＿。

（注：非专利技术转让合同当事人可以依照专利实施许可合同，采取独占，排他，普通许可证的形式。）

4.使用本非专利技术的范围：＿＿＿＿＿＿＿＿＿＿＿

（注：使用范围指地域范围、期限范围、使用方式范围。）

5.转让方的主要义务：

（1）在合同生效之日起＿＿＿天内，向受让方交付下列技术资料：＿＿＿。

（2）在合同履行过程中，向受让方提供下列内容的技术指导和服务：＿＿。

（3）保证所转让的技术具有实用性，可靠性，即为能够应用于生产实践的成熟技术。保证使用本非专利技术能够达到下列技术经济指标：＿＿＿＿＿。

6.受让的义务：

（1）向转让方支付使用费，数额为＿＿＿＿元。按下列日期分期支付：＿＿＿＿

（注：在采取提成支付的情况下，当事人可以约定：a.合同生效后＿＿＿日内先向转让方支付＿＿＿＿元；b.自合同产品投产之日起（或第一件合同产品销售之日起）＿＿＿＿年内接产值（或销售额、或利润）的＿＿＿＿＿％向转让方支付提成费。提成费每年支付一次，支付日期为每年＿＿＿＿月＿＿＿日前。）

（2）按照合同约定的范围使用本非专利技术。

7.保密条款

在本合同有效期内，双方当事人应对下列技术资料承担保密义务：＿＿＿＿＿。本合同期满后＿＿＿＿年后，双方当事人应对下列技术资料承担保密义务：＿＿＿＿。

8.合同产品的验收标准和方法：＿＿＿＿＿＿＿＿。

9.后续改进条款

在本合同履行过程中，双方当事人各自在本转让技术基础上做出的新的发明创造专利权归做出发明创造的一方所有，但当事人另有约定的除外。

10.转让方的违约责任

（1）转让方不按照合同约定向受让方提供技术资料及技术指导，应视不同情况，返还部分或全部使用费，并支付数额为＿＿＿＿的违约金；

（2）转让方逾期两个月不向受让方提供技术资料及技术指导，受让方有权解除合同，转让方应当返还使用费，并支付数额为＿＿＿＿的违约金；

（3）转让方违反合同约定的保密义务，泄露技术秘密，使受让方遭受损失的，转让方应当支付数额为＿＿＿＿的违约金。

让与方实施使用该非专利技术超越约定的范围的，违反约定擅自许可第三人实施该项非专利技术的，应当停止违约行为，支付违约金或赔偿损失。

11.受让方的违约责任

（1）受让方未按合同约定的期限和方式支付使用费，应补交使用费外，应向转让方支付数额为＿＿＿＿的违约金，受让方拒不交付使用费或违约金，除必须停止使用非专利技术外应当返还技术资料，支付数额为＿＿＿＿＿的违约金；

（2）受让方逾期两个月不支付使用费，转让方有权解除合同，受让方应当停止实施被转让的技术，返还技术资料，支付数额为＿＿＿＿的违约金；

共2页，当前第1页12

公司采购合同范本

甲方：________________

乙方：________________

________________管理有限公司( 以下简称甲方 ) 与___________服装服饰有限公司 (以下简称乙方) 就工服制作业务签订以下合同，共同遵守。

第一条 产品名称、价格、数量。

后附详细报价单。此价格经双方认可，作为本合同的附件。

第二条 交货地点及时间

1.地点：__________________________________________

2.时间：自本合同签订且乙方收到预付款后______日内。

第三条 加工形式

1.乙方根据甲方要求提供服装款式及面料样品，经双方确认后，再进行批量生产。

2.采取乙方包工包料并提供全部辅料的方式。

3.货物到达甲方指定地点后，甲乙双方依据订货清单进行清点验收，并办理交接签字手续。

第四条 甲方责任

1.甲方通过服装款式及面料后，在合同生效及执行过程中不得擅自更改。

2.甲方定好量体时间，保证人员齐全。

3.按此合同付款日期，按时付款。

第五条 乙方责任

1.乙方须保证产品质量，如有制作问题，乙方须负责修改。

2.按此合同交货日期，按时交货。如未按时交货，甲方将扣除乙方______________的货款作为违约金。

第六条 结算方式

1.支票结算。此合同签订后____日内，甲方须预付_____________的货款给乙方。

2.终结付款额，依据实际制衣件数，经双方认可后的款额支付。

3.甲方收到乙方全部货物并验收合格后，须在_____________内付清乙方全部货款。如有延误，每日须加付_____________的滞纳金。

第七条 本合同有效期自签订之日起生效，到全部货款结清之日为止。

第八条 此合同经双方签字盖章后生效。如有一方在有效期内欲终止合同，需赔偿对方______________的货款作为违约金。本合同一式两份，双方各执一份。

甲方业务代表：__________ 乙方业务代表：____________

甲方盖章：______________ 乙方盖章：________________

日期：__________________ 日期：____________________

技术顾问聘用合同模板

甲方 :

乙方:

甲、乙双方依据《中华人民共和国合同法》相关规定，就甲方聘用乙方一事达成协议内容如下，并订立本合同，以兹双方共同信守。

一、聘用岗位。

甲方聘用乙方担任本公司的技术总顾问，全权负责公司的 技术开发和研制、技术革新和改进、技术的保密和管理、技术指导和咨询服务等。

二、聘用时间。

时间总计为 年，自 年  月  日开始起算至年  月日止。合同每年一签，每年期满双方重新

签订。

三、聘用报酬。

乙方的报酬由两部分构成，一是年薪  元，支付方式：每月支付元，剩下的在年底一次性支付。第二部分是技术开发成果奖励，按照每提供或研制开发一项符合市场推广标准的技术，在根据该技术成果进行生产销售  个月后，确能够带来经济效益的，一次性从每年销售利润中支付乙方万之奖励。

四、技术成果及归属。

乙方主要为甲方提供和研制  等技术或配方。乙方在甲方任职期间，因履行职务或者主要是利用甲方的物质技术条件、业务信息等产生的发明创造，有关的知识产权均属于甲方所有。甲方可以在业务范围内充分自由的利用、生产经营或者向第三方转让。乙方在离职后无权再继续使用该技术或转让该技术。

五、技术成果的标准要求及开发时间、验收。

试验阶段自 年月日至  年  月  日， 年  月至  月  日为试生产阶段。

六、保密责任。

1、乙方任职期间的保密义务。

乙方除了履行职务的需要之外，承诺下列保密义务：

(1)乙方在任职期间，必须遵守甲方规定的保密规章、制度，履行与其工作岗位相应的保密职责；

(2)未经甲方同意不得泄露、告知、转让或者其他任何

方式使任何第三方知悉属于甲方或者属于他人但甲方承诺有保密义务的技术秘密或其他商业秘密信息；

(3)乙方承诺，在甲方任职期间，非经甲方事先同意，

不再与甲方生产、经营同类产品或提供同类服务的其他企业、事业单位、社会团体等担任任何职务，不为他人类似经营提供任何建议；

2、乙方离职之后的保密义务。

双方同意，乙方离职之后仍对其在甲方任职期间接触、知悉的属于甲方或者虽属于第三方但甲方承诺有保密义务的技术秘密和其他商业秘密信息，承担如同任职期间一样的保密义务和不擅自使用有关秘密信息的义务，而无论乙方因何种原因离职；

七、乙方在任职期间应该遵守公司的管理制度或财务制度。乙方在岗位上的食宿由甲方负责人提供，因公出差费用由公司负担。

八、违约责任

甲乙双方任何一方违反本合同之约定造成对方损失的，应该按照损失的大小承担违约赔偿责任。

九、争议的解决

本合同经双方签字公章后生效。因履行本合同发生的争议，双方协商解决，协商不成的，通过仲裁或法律途径解决。

十 、本合同一式份,具有同等法律效力,甲乙双方各执一份。

甲方：乙方：

（签章）（签章）

签订日期：年  月  日

商业储运公司仓库（简称甲乙方）包仓合同

（      ）包仓字第      号

为妥善解决乙方商品储存总是现商定由甲方划出库房面积，采用包仓形式安排存放乙方指定的商品，按甲方现形仓租标准________品等租率计收仓租，经双方协商同意共同条款如下：

（一）甲方划定第________分仓第________号库房实际面积________平方米，按包仓的形式储存放乙方________商品。

（二）商品入仓时，乙方必须遵守甲方仓库管理制度，做到货单同行，包装牢固（危险品应按危规所规定的包装标准），提货时必须使用正式提货单。

（三）乙方包仓的面积如需改储商品种时，必须事先征得甲方同意，否则，甲方可以拒收。改储商品品种的仓租，可按仓租标准等级租率，计收仓租。

（四）仓租结算每月分两期，第一期每月________日________日，第二期________日一下月________日由乙方开户银行：________账号________划付。

（五）合同自签订之日起生效。有效期________个月。________年________月________日止，期满后另行商议。

（六）本合同一式________份（正本二份，副本________）双方各执正本一份。甲方副本________份，乙方副本________份据以执行。

（七）本合同必须经甲方仓储科审核盖章后方能生效。

甲方（盖章） _____________________  乙方（盖章）_____________________

联系人：__________________________  联系人：_________________________

电话：____________________________  电话：___________________________

公司仓储科（盖章）_______________

_________年_______月_______日签订

代理公司注册登记协议书范本3篇

公司注册流程依次为：查名(确定公司名字)→开验资户→验资(完成公司注册资金验资手续)→签字(客户前往工商所核实签字)→申请营业执照→申请组织机构代码证→申请税务登记证→办理基本帐户和纳税账户→办理税种登记→办理税种核定→办理印花税业务→办理纳税人认定→办理办税员认定→办理发票认购手续。以下是第一范文网小编为大家精心准备的：3篇代理公司注册登记协议书范本。内容仅供参考，欢迎参考阅读!

代理公司注册登记协议书范本一

甲方：___________

地址：___________

电话：___________

联系人：_________ 乙方：___________

地址：___________

电话：___________

联系人：_________

为了充分发挥_________的资源和信息服务优势，甲、乙双方经过友好协商，本着平等互利、友好合作的意愿达成本协议书，并郑重声明共同遵守：

一、甲方同意按照本协议的规定，授权乙方为其代办公司注册手续。

二、乙方提供的代办咨询服务范围仅限如下：

1.为甲方代办工商营业执照、组织机构代码证、税务证、三章(法人章、公章、财务章);

2.约定的其他服务：

_________。

三、甲方的责任：

1.甲方应指定专人配合乙方完成新企业工商登记注册等事务，并提供齐全的证件和规范的法律文件资料。

2.甲方对提供的证件和法律文件资料的真实性、正确性、合法性承担全部责任。

3.甲方承担向工商、税务、技监等机关缴纳的有关费用。或者由甲方提供经费，由乙方代为缴纳。

四、乙方的责任：

1.乙方应遵守国家有关法律、法规，依照规定从事企业登记代理工作。

2.乙方自觉接受工商行政管理机关的指导和监督，采用规范的登记代理程序和方法，协助委托方完善各类文件资料，齐全应有的证件。

3.乙方对甲方提供的证件和资料负有妥善保管和保密责任，乙方不得将证件和资料提供给与新企业开业登记(包括工商、技监、税务等部门)无关的其他第三者。

五、费用

1.本协议书所涉及的费用的货币单位均为人民币。

2.本项工商登记咨询代理工作收取总代理费为人民币(大写)_________元，领取营业执照、组织机构代码证和税务证时由甲方向乙方交付。

3.甲方与乙方签订本协议时，需向乙方缴纳代理费的_________%作为预付款，甲方签署本协议后单方面停止履行或违反本协议内容，乙方有权不予返还预付款。

4.甲方与乙方签订本协议时，需向乙方提供_________元人民币，作为代理过程中相关部门小额收费项目代付款，在代理业务中止或完成时统一结算。

5.甲方将_________%代理咨询费用和小额工商行政收费预交纳给乙方时，乙方为甲方开具收据。在乙方将全部预定的材料交给甲方，双方进行结算时，乙方将在随后相应单位开具的正式发票和乙方自行开出的咨询代理发票交给甲方，甲方将原相应收据退还乙方。

6.在委托咨询服务过程中，所有必要的费用(如名称登记准费、场地租赁费、验资费、公告费等政府收费)由甲方自理。

六、若由于乙方原因或其他原因造成企业注册登记申请失败，乙方向甲方退还甲方交纳的全部代理咨询费用，并退还甲方全部资料。

七、乙方根据甲方提供的信息撰写材料，甲方确认无误后签名盖章，意味着甲方认可乙方撰写的材料符合甲方的真实情况，并对申请材料的真实性负全部责任，如果因为材料不真实造成的一切后果，均由甲方承担，与乙方无关。

八、乙方和甲方在执行协议中发生的一切争执应通过双方友好协商解决。

九、由于人力不可抗拒因素，如火灾、水灾、地震、雷击等自然灾害或者罢工、战争、政府强制措施、政府政策变更等原因而影响本协议的执行，双方不负违约责任，根据事故影响的时间可将协议履行时间相应延长，并由甲乙双方协商补救措施。

十、协议的生效及其它：

1.本协议签字盖章和授权代表签字后即时生效。协议正本一式两份，甲乙双方各执一份，具有同等效力。

2.本协议若因某种原因失效，或提前解除，或申请失败，甲方应将乙方制作的所有材料归还乙方或者销毁，并不得在以后任何情况下使用乙方提供的材料，或模仿抄袭乙方提供的材料的内容，否则甲方应按照本协议费用的5倍金额赔偿乙方，并保证以后不得再有此侵权行为。

3.本协议未尽事宜由甲乙双方另行协商。

甲方(盖章)：_________ 乙方(盖章)：_________

代表(签字)：_________ 代表(签字)：_________

_________年____月____日 _________年____月____日

代理公司注册登记协议书范本二

甲方(委托方)：__________________

乙方(受托方)：__________________

甲方因业务发展需要欲在香港成立公司，现全权委托_________公司向香港有关机构申请办理公司注册相关手续，经双方协商一致，达成如下內容条款：

一、甲方必须向乙方提供真实有效的股东资料：身份证(或护照)复印件、个人住址(或通信地址)，联络电话。

二、填“注册香港公司委托书”一份：公司中英文名称、董事详细资料。

三、甲方向乙方提供的资料必须有确认真实无误，保证申请注册的公司是用于合法的商业运作，并承担该公司的债权债务和法律责任。

四、乙方为甲方代理细则如下

a.到香港公司注册审查确定公司名称，付代查册费。

b.提供香港公司注册地址，法定秘书服务。

c.制作公司钢印一枚，代付登记年费。

d.制作公司签字章、代付印章费。

e.制作公章一枚，代付印章费。

五、办理费用和付款方式

a.办理总费用_________(人民币)元(包括须向香港政府有关部门交納的费用和乙方代理费用)。

b.付款方式：申办前(甲方填委托书，协议书)預付________(人民币)，收到法定文件签名后，再付________元(人民币)

六、办理的时间：收到甲方签署申请成立公司法定文件和申报表后10个工作日。

七、本协定双方订立后，如乙方无法完成甲方委托之业务，甲方此前所交的款项乙方給予乙方退还。

八、本协定一式两份，甲乙双方各执一份，本协定自双方签署之日起生效，未尽事宜双方共同协商解決。

甲方(盖章)：_________

代表(签字)：_________

_________年____月____日

乙方(盖章)：_________

代表(签字)：_________

_________年____月____日

代理公司注册登记协议书范本三

甲方：_______国际集团有限公司

乙方：_______________________

一、经协商：乙方因业务发展需要欲在香港成立公司，现全权委托_________________国际集团有限公司向香港有关机构申请办理公司注册相关资料：

中文名称：_____________________________________________

英文名称：_____________________________________________

注册资本：____________;服务收费总金额：( _______港币)全包

备注：_________________________________________________

二、经双方协商一致，达成以下内容条款

a)到香港公司注册署查册确定公司名称;

b)核实注册资本、股东数目以及股份比例;

c)确定首批股东、秘书、董事和董事会主席委任及呈报;

d)准备所有的文件和法定的申报表，安排股东签署文件，向政府有关部门提出申请;

e)在注册处代申请人宣誓成立公司，代付注册资本登记;

f)申领公司股份证明、股份分配文件及代付印花税;

g)申领公司注册证书，代付注册费;

h)申请税务局商业登记，代付登记年费;

i)向政府印务局申印公司组织大纲、公司章程_______本，法定记录和公司股票各一本，代付费用;

j)制作公司钢萤签字章、圆胶章各一枚，代付印章费;

k)免费提供第一年的电话、传真、地址和秘书服务费。

三、甲方保证现成公司无任何债权、债务、纠纷，若出现纠纷完全由甲方负责。乙方必须向甲方保证不会利用已注册之公司作非法用途，否则所有法律责任由乙方负责。

四、公司全套注册手续 _______-_______个工作日完成，签署合同时乙方需付__________________元人民币作为定金。余款在交接全套手续时全部付清。

甲方代表：_________________

电话：_____________________

日期：_____________________

乙方代表：_________________

电话：_____________________

日期：____________________

防雷技术服务合同

甲方：______县气象局

乙方：______________

为了更好地保证建筑物防雷工程部分符合技术规范，杜绝因防雷设施不合格而返工的现象，根据《重庆市雷电灾害防御管理办法》的规定，经甲、乙双方协商，约定如下：

一、甲方负责对乙方________项目进行防雷工程部分施工图设计审核和现场施工监审。

二、施工图设计审核需乙方提供施工图纸一套(施工图应有防雷设计平面图及相应说明)，并填写申请表。甲方在乙方资料完备的情况下，一个工作日内完成审核、提出审查意见，符合要求的发给审核证书。

三、现场施工监审应分别在安装接地体和焊接引下线、安装接闪器时由乙方电话联系乙方到施工工地进行实地指导和分段测试，并填入相应报告表。此表是防雷工程验收的重要依据。预计施工监审时间为：________ 。

四、根据重庆市物价局文件(渝价[20xx]402号)规定，乙方应缴纳：

1.图纸设计审核费________元。(工程预算的________‰)

2.施工监审费________元。(每次________元)

两项费用总计________?元(大写________万________仟________佰________ 拾________元)。

五、甲方有责任对乙方提出的要求及时进行办理;乙方有义务提供准确的资料，及时联系甲方，对甲方提出的问题及时整改。

六、以上条款，甲、乙双方如有违反，将按照《中华人民共和国气象法》、《重庆市防御雷电灾害管理办法》的有关规定，给予处罚。

甲方(签章)：_____________

乙方：_____________________

_______年_______月_______日

公司培训合同

甲方： 公司

乙方： 身份证号码：

户籍地：

甲乙双方秉持诚信公平原则，互相协商就甲方委派乙方_______________________事宜达成以下协议：

1.甲方委派乙方自_____ 年____ 月____ 日起至 _____年_____ 月_____ 日 止赴___________ 进行 _____________。

2.乙方___________ 培训期间所产生的费用，按照人事管理制度和财务作业流程报支。

3.乙方目前任职于_______ 公司 ______部门，担负 _______工作。乙方批准甲方的上述安

排并批准自愿延伸劳动合同期限 _______年，即劳动合同至________ 年 ______月_________ 日终止。在上述期限内，乙方应持续从事甲方安排的工作。非因不可抗因素导致乙方不能履行劳动合同时，乙方承诺不单方面提出解除劳动合同。

4.乙方请求提前解除劳动合同，经协商甲方批准时，劳动合同即解除，但乙方应赔偿甲方为乙方__________ 培训交换支付的费用。

赔偿金额依下列公式盘算：

赔偿金额＝因培训所产生费用总额＊未服满劳动合同期/应延伸劳动合同期

5.甲方不批准乙方提前解除劳动合同，乙方执意解除或擅自离职或因违法、违纪被公司辞退的，除按上述公式盘算赔偿金外，还应交纳违约金。违约金依下列公式盘算：

赔偿金额＝因培训所产生费用总额＊未服满劳动合同期/应延伸劳动合同期

（培训所产生的培训费用包含：培训之学费、杂费、办理相干证件费用、培训期间所产生的住宿、膳食、交通、出差补贴、交换费用等在甲方实际报支或由甲方实际支付的费用）

6.乙方提前解除劳动合同的违约金/或赔偿金应于甲方办理终止劳动合同手续前交纳。

7.乙方向甲方供给担保人______________（身份证号码___________________，户籍地_____________________，任职__________________，担负________________),保人应向甲方出具担保书，保证乙方履行本协议书的任务。在乙方解除劳动合同时，担保人向甲方承担的保证责任，保证乙方按约定支付赔偿金/或违约金。

8.本协议自双方签定之日起生效，至乙方劳动合同期满后终止。

9.本协议书一式两份，具同等效率，甲乙双方各持一份。

甲方代表（公章）乙方：

年月日年月日

担 保 书

兹为 __________________同志在x有限公司工作期间外派培训事宜供给担保：

1、 保证遵守《培训协议书》，遵守公司管理规定。

2、 如违背《培训协议书》，我愿意承担由此行动所带来的责任。

担保人（签名）：_________________

担保人接洽电话：________________

担保人工作单位：________________

担保人与被担保人关系：________________

____年_____月____ 日

甲方：

法定代表人：

注册地址：

通讯地址：

邮政编码：

乙方：姓名_____性别___

居民身份证号码：

出生日期____年__月__日

家庭住址：

户口所在地：

通讯地址：

邮政编码：

联系电话：

鉴于乙方系某某公司(明确公司名称)会计人员，在甲方利用业余时间兼职从事会计劳务工作。甲乙双方经平等协商，共同决定建立兼职劳务关系。甲乙双方在充分明确这一法律关系的基础上，根据《民法通则》和《合同法》等其他相关法律、法规，自愿签订本协议，共同遵守协议所列条款。

一、协议期限

本协议期限自______年____月____日起，至____年____月____日止。合同期满时，双方可以另行办理续签事宜。

二、工作条件

甲方应根据国家有关规定，为乙方提供符合职业安全卫生条件的工作环境。

三、工作范围:

1.根据甲方提供的原始凭证和其他资料，乙方代理甲方进行一般的建帐，建制和记帐、算帐、报帐、办理甲方各项纳税事宜。

2.做好各类纳税报表，凭证及帐册，每年年底之前做好各类综合报表，年鉴报表等各种财务所需帐目凭证，保证甲方正常营业，并顺利通过税务审计以及甲方年检;

3.甲方遇到查帐或审计，乙方应予以配合，就所采用的会计政策等作出解释。

4.完成甲方交付的其它工作任务。

四、甲方权利和义务

1.甲方有权为乙方安排财务会计工作，分配任务;并检查乙方的工作情况。

2.甲方提供给乙方的会计资料必须取得符合国家统一会计制度规定的原始凭证，原始凭证应当真实，合法，准确，并应配有专人负责日常收支和原始凭证的保管工作。

3.甲方按照约定劳务报酬及时足额的支付乙方劳务报酬。

五、乙方权利和义务

1.根据甲方提供的原始凭证和其他资料，按照国家统一会计制度的规定，进行会计核算，并负责妥善保管好甲方的相关财务单据，原始凭证和资料等。

2.在提供劳务期间，乙方应严格遵守国家各项法律规定;遵守甲方的工作规范、操作规程、劳动安全卫生制度等各项规章制度，乙方自行承担人身安全责任。

3.为甲方提供会计、税务等方面的咨询服务，使甲方在合法合理前提下，享受税务政策，提高经济利益。

4.乙方对甲方提供的各项原始凭证进行会计核算，保证会计凭证，账簿及报表的真实性，合法性和准确性。

5.乙方不得从事有损于甲方声誉的活动，严禁泄漏甲方的商业秘密和有关财务数据，若乙方泄露甲方商业秘密或者财务数据，甲方有权要求乙方支付金额为三个月劳务报酬的违约金，并承担相应赔偿责任。

六、劳务报酬

甲乙双方约定，乙方劳务报酬每月为________元(人民币)。

七、协议的解除与终止

1.乙方因病或人身意外事故无法继续履行职务，合同自行解除。

2.在本协议履行期限内，乙方辞职，须提前三个月提出书面申请。否则甲方有权要求乙方支付金额为三个月劳务报酬的违约金。但甲方不按本协议约定提供劳务报酬时，乙方可以随时解除本协议，不受提前通知的限制。

3.乙方提供劳务不符合要求或者乙方违反工作纪律或违背职业道德，甲方有权随时单方解除本协议。

4.甲乙双方无论因何原因解除或终止本协议，乙方均应立即办理工作交接、归还甲方财、物等离职手续。具体程序如下：

乙方离职时应按规定交还公司用品等，直到离职手续完成为止，公司才发放最后一次劳务报酬;如离职时没有完成归还甲方财、物等离职手续而离开，甲方有权在不违反公布及可公开获悉的法律、法规的原则下，扣除乙方相应的劳务报酬。

八、其他

1.乙方的人事档案仍由原单位管理，甲方不负责处理与乙方人事档案有关的任何事宜。

2.因甲乙双方之间建立的关系是兼职劳务关系而不是劳动关系，因此甲方不承担社会保险缴纳义务。

3.甲乙双方约定，乙方自行购买意外伤害保险，乙方在为甲方提供劳务过程中发生意外伤害均与甲方无关。

4.双方如因履行协议发生争议，应首先友好协商解决。协商不成，任何一方都有权向甲方所在地人民法院提起诉讼。

5.本协议一式两份，甲乙双方各执一份，自签订之日起生效。

甲方(盖章)： 乙方(签字)：

日期： 年月日 日期：年月 日

技术合同：涉外许可证合同

鉴于双方合作的愿望，本着平等互利的原则，经过友好协商，供方同意给予受方在中国设计、制造、使用和销售_________专利的权利(以及使用_________商标的权利)。该专利已是乙方在工业上使用的对象，已制造过_________产品。

一、合同范围

1.供方同意受方在中国设计、制造、使用和销售合同产品的专有技术(或专利技术)。在该地区受方享有利用该技术独占性制造产品和销售产品的权利(或这是一项非独占的许可证)。

2.供方负责向受方提供_________技术的研究报告、设计、计算、产品图纸、制造工艺、质量控制、试验、安装、调试、运行、维修等一切技术数据、资料(详见附件_________)和经验，以便受方能实施制造产品(产品的型号、规格、技术参数等详见附件_________)。

3.供方负责自费派遣技术人员赴受方进行技术指导和参加_________的性能考核(详见附件_________)。

4.供方负责接受受方有关人员自费赴供方进行培训，使受方人员能掌握合同规定的上述技术(详见附件_________)。

5.在合同有效期限内，受方在合同产品上有权使用属于供方所有的_________商标(或牌号)。

6.供方有责任(或同意)以最优惠的价格向受方提供为制造合同产品所必需的设备、测试仪器、原材料及零部件(或供方有责任帮助受方为实施制造合同产品所需的配套件，从第三方取得有关技术许可证，或者与第三方进行合作生产)。

二、价格或许可证使用费

1.根据本合同规定，供方向受方提供的技术和技术服务等，受方应向供方支付的合同总价为_________元，其中：技术使用费_________元;资料费_________元;技术服务费_________元。上述价格为固定价格。

2.受方有义务对根据许可证转让的技术支付下列费用：

(1)入门费_________元。

(2)受方在合同有效期内应向供方支付常年提成费，其提成率为合同产品净销售价的3%。

三、技术资料的支付

1.供方应按本合同附件_________的规定向受方提供技术资料。

2.供方用空运把技术资料送达中国_________机场。该机场在收到技术资料后而在空运提单上加盖的印戳日期为技术资料的实际交付日期。受方将带有到达印戳日期的空运提单影印本1份寄送供方。

3.在技术资料发运后的24小时(或48小时)内，供方应将合同号、空运提单号与日期、资料项号、件数、重量，航班号用电报或电传通知受方，并将空运提单正本1份、副本2份和技术资料装箱清单3份航空邮寄给受方。

4.如受方收到技术资料后发现不符合合同附件_________的规定，包括在空运中丢失或损坏，应在30天内通知供方，说明所缺或损失的资料，供方应在收到通知后立即(或30天内)免费补寄或重寄给受方。如果受方在收到技术资料后60天内没有提出资料不足或损坏的书面通知，即视为受方对技术资料已验收。

5.技术资料使用文字为英文(或其他文字)，计量单位为米制，技术资料所适用的标准为_________工业标准。

6.技术资料的包装要适应长途运输与搬运、防雨、防潮。每箱上应以英文标明下述内容：合同号(许可证合同编号)、收货人(_________)、目的地(中国_________市机场)、毛重(_________公斤)、箱号(或件号)以及运输标志等。

四、交换改进技术及对技术资料的修改

1.供方在合同有效期内改进和发展的技术资料，应免费提供给受方。受方改进和发展的技术也应按对等原则提供给供方，但改进和发展的技术所有权属于受方，对方不得去申请专利或转让给第三方。双方交换技术资料，均不附加任何限制。

2.供方提供的技术资料，如有不符合于受方生产条件的，供方有责任协助受方修改技术资料，并加以确认。

五、性能考核和验收

1.在合同产品首批生产后，由双方根据本合同附件_________的规定，共同进行产品性能考核。

2.经考核合同产品的性能符合合同技术文件规定的技术指标，即通过验收，双方签署合同产品性能考核合格证明书一式4份。每方各执2份。

3.如经考核，合同产品性能不符合本合同技术文件规定的技术指标时，双方应共同研究，分析原因，澄清责任。如责任在供方，供方应自负费用，采取措施，消除缺陷。缺陷消除后进行第二次考核。如果第二次考核后仍不合格，供方应继续采取措施，消除缺陷，并进行第三次试验。如果第三次考核仍不合格时，受方有权终止本合同。如果考核不合格责任在于受方，受方在供方协助下，采取措施，消除缺陷，并进行第二次或第三次试验。如第三次考核仍不合格时，则由双方协商如何再执行合同的问题。供方协助受方消除缺陷，派遣技术人员的交通和食宿费用由受方负担。

共2页，当前第1页12

中外合资经营企业劳动合同（一）

甲方（用人单位）：_______________________

地址：___________________________________

法定代表人（主要负责人）：_______________ 乙方（劳动者）：_________________________

性别：___________________________________

年龄：___________________________________

身份证号码：_____________________________

现在住址：_______________________________ 甲方因生产（工作）需要，招聘_________（以下简称乙方）为甲方员工。根据《中华人民共和国中外合资经营企业法》、《中华人民共和国劳动法》和《中外合资经营企业劳动人事管理条例》的有关规定，经甲、乙双方协商，特签订本劳动合同，以共同遵守。 第一条 生产和工作任务的要求

甲方根据生产（工作）需要，安排乙方任_________工种（岗位），以后可以根据生产经营需要和乙方的业务能力及表现，调整乙方的生产（工作）岗位，并及时签订变更合同。 第二条 合同期限

合同有效期为_________年，自_________年______月______日至_________年_________月______日（其中试用期为_______个月，自_________年_____月______日至_________年_____月______日）。试用期满，合格的定岗使用，不合格的甲方有权调整乙方的生产（工作）岗位，或予以辞退。 第三条 工资待遇

甲方根据乙方现任职务或工作岗位，确定乙方月标准工资为_________元，各种津贴按有关规定享受。今后，根据生产经营情况和乙方表现逐步提高乙方工资收入。乙方的原工资等级和月标准工资作为档案工资予以保留。 第四条 劳动保险、劳动保护和福利待遇

1.甲方按规定缴纳和办理乙方养老保险基金手续，向乙方支付当地政府规定的卫生费、交通费、书报费等各种津贴，并享受国家规定的法定节假日、公休假、婚丧假、探亲假以及女职工孕期、产期、哺乳期等。

2.甲方必须执行国家有 关劳动保护、女工特殊保护等法规，采取劳动保护措施，保护安全生产和乙方健康。甲方应根据企业生产、工作的需要，发给乙方劳动防护用品和保健食品。

3.甲方实行国家现行工时制度。甲方应严格控制延长乙方的工作时间，确需加班加点，应发给乙方加班工资，每月加班不得超过36小时。

4.员工患病或非因工负伤，给予_________个月的医疗期。医疗期满仍未治愈的，经双方协商可再给予_________年以内的医疗期。医疗期内的医药费和病假工资由甲方承担。医疗期满不能从事原工作的，甲方根据需要，安排乙方从事力所能及的工作。

5.员工因工负伤，致残或患职业病，医疗期医疗费用，工资待遇，按国有企业标准，由甲方承担，直到医疗终结。伤愈后由甲方安排力所能及的工作。

6.员工因工死亡，按国有企业规定，由甲方负责支付死亡丧葬补助和职工供养直系亲属抚恤费，生活困难补助费。 第五条 劳动纪律和奖惩办法

1.甲方根据生产情况负责制订工艺流程、操作规程和有关生产标准或工作规范，乙方保证严格执行。

2.乙方对甲方生产（工作）有特殊贡献，应给予乙方精神和物质奖励。乙方违反劳动纪律或犯其他错误，甲方应在坚持思想教育的前提下，可给予相应的处分或处理。甲方应在作出辞退或开除决定前_______天通知工会，并报主管部门和劳动部门备案。 第六条 甲、乙双方解除合同条件

1.符合下列情况之一，甲方可以解除劳动合同：

（1）乙方在试用期内，发现不符合录用条件的；

（2）乙方患病或非因工负伤，在规定的医疗期满后不能从事原工作或其他工作的；

（3）乙方严重违反劳动纪律；

（4）企业宣告解散、破产或濒临破产处于法定整顿期间的。

2.乙方被劳动教养和判刑的，劳动合同自行解除。

3.下列情况之一的，甲方不得解除劳动合同辞退乙方：

（1）乙方因病或非因工负伤在规定医疗期内的；

（2）乙方因工负伤或患有职业病，在治疗、疗养期间和医疗终结经劳动鉴定委员会确认部分或者全部丧失劳动能力的；

（3）实行计划生育的女职工在孕期、产期和哺乳期间的；

（4）合同期限未满又不符合本合同解除条件的。

4.下列情况之一的，乙方可以向甲方提出解除劳动合同：

（1）经国家 有关部门确认，甲方劳动安全、卫生条件恶劣，严重危害乙方身体健康的；

（2）甲方不按合同规定支付劳动报酬的；

（3）甲方不履行合同或违反国家有关法律、法规，侵害乙方合法权益的；

（4）乙方有正当理由要求辞职并经甲方同意的。 第七条 甲、乙双方中止或解除合同后经济补偿

1.除本合同第六条第1款第（1）、（3）项和第2款人员外，甲方解除乙方合同应在30日前通知乙方。

2.对于终止劳动合同的员工和按第六条第1款第（2）、（4）项规定辞退的以及按第六条第4款第（1）、（2）、（3）项规定辞职的，甲方应根据乙方在甲方企业的工作年限，每满1年发给相当于本人1个月实得工资的生活补助费。

3.对于按照本合同第六条第1款第（2）项规定辞退的，甲方除发给乙方生活补助费外，还须发给乙方相当于本人3至6个月实得工资的医疗补助费。

4.对于按照本合同第六条第1款第（4）项规定辞退的，甲方除发给生活补助费外，还须发给乙方相当于3至6个月实得工资的辞退补偿金。

5.对于按照本合同第六条第4款第（4）项规定，乙方有正当理由向甲方提出辞职的，甲方一般应予以同意，但应在30日前向甲方提出，经甲方批准后可办理解除合同手续。如经甲方出资培训，乙方应赔偿甲方一定数额的培训费。 第八条 违反劳动合同应当承担的责任任何一方违反劳动（聘用）合同，给对方造成损失的，应当根据其后果和责任大小予以赔偿。其中，责任属于甲方的，应继续履行合同，同时负责赔偿在合同中断期间乙方的经济损失；责任属于乙方的，赔偿招工（招聘）和技术培训费用。 第九条 争议的解决劳动争议发生后，当事人可以向本单位劳动争议调解委员会申请调解，调解不成，当事人一方要求仲裁的，可以向劳动争议仲裁委员会申请仲裁，当事人一方也可以直接向劳动争议仲裁委员会申请仲裁。对仲裁裁决不服的，可以向人民法院提起诉讼。 第十条 其他事项____________________________________________。