技术岗位 管理岗位通用20篇

甲方：德铭大药房有限公司

乙方：

为了更好的服务广大群众，完善经营和管理，甲方聘请乙方为如皋德铭大药房有限公司企业负责人，经双方共同商议签订聘请合同如下：

一、 乙方职责

1、 制定药房的整体发展规划。

2、 负责审核制定药房投资项目计划、管理药房业务操作流程。

3、 负责药房整体业务拓展，指定药房各种工作计划、各种规章制度和整体营销管理工作。

4、 负责药品的采购、上柜、经营管理工作。

5、 推动各项管理规章制度的建设和完善。

二、 甲方职责

1、 负责对药房进行各种经营许可证件的办理工作。

2、 负责企业各种所需的资金开支。

三、 本合同的有效期为一年，合同期限自20xx年5月31日开始计算。

本合同一式两份，甲乙双方各执一份。

甲方签字： 签字日期：

甲方：

乙方：

为明确供电企业(简称甲方)和双电源(自备电源)用电客户(简称乙方)在电力供应与使用中的权利和义务，安全、合理、有序地供电和用电，根据《电力法》、《电力供应与使用条例》、《供电营业规则》及《农村安全用电规程》等电力法规的规定;经双方协商一致，达成以下协议，共同信守、严格履行。

一、乙方根据用电需要向甲方申请双电源供电，需向甲方提供双电源用电申请书并附有有关资料图纸和自备发电机组的设备参数和技术资料，经甲方审核批准后按图纸施工，甲方验收合格后方可办理供电手续。

二、供电方式、安装地点及产权分界

1、甲方从 线 号高压杆或从 线 变台 号低压杆接线向乙方供电。

2、乙方自备电源(自备发电机)共 台，容量： 千瓦,电压： 伏，厂家:

，型号: ，安装日期: ，安装地点: 。

3、甲方与乙方的产权分界点：高压供电在 线 号高压杆高压计量箱进线T接点处;低压供电在 线 变台 号低压杆 计量电度表进线处;具体接线方式及分界点详见附图《供电接线及产权分界示意图》。

三、供用电设施维护管理责任

1、供用电双方按本协议第二条的产权分界各自负责设备的维护管理。

2、供用电双方各自分管的供电设施，除另有约定外，未经对方同意，不得操作或更动;当遇到危及电网和用电安全，或可能造成人身伤亡、设备损坏，或违约用电、窃电、欠费时;甲方可根据实际情况更动或操作用电方的供电设备。

3、乙方负责保护并监视受电装置内用电计量装置及电力负荷管理装置的正常运行;如有异常，乙方应及时通知甲方。

三、 安全运行管理责任

1、乙方的低压两相自备电源应采用双投刀闸切换电源，低压三相四线自备电源应采用低压四极双接刀闸，如因条件限制(距离过远或总屏刀闸容量在1000安以上时)，可采用电气闭锁，但切换电源时，不允许有合环和并列的可能。

2、乙方的高压自备电源，电源侧的断路器，应采用机械联锁装置，如开关柜距离过远，可采用电气闭锁，但应保证任何情况下，只有一路电源投入运行，而无误并列、误合环的可能;在进户终端杆装置隔离刀闸，该刀闸操作权属甲方。

3、甲电方双电源投入运行时，必须先做核相检查以防非同相并列;乙方在架空线路或电缆线路上从事有可能导致相位变化的工作、配电室(箱)主接线发生变化、主变压器更换或大修后在重新投运时也必须作核相工作。

4、 乙方不允许高低压双电源并列运行者，必须在电源开关或刀闸上装设可靠的联锁装置。

5、乙方不得擅自变更主备电源运行方式;不得超过批准的备用用电容量用电。

6、凡经甲方同意二条高压馈线分别同时供电的乙方，其低压侧应各自分开线路供电，严禁合环运行;同时严禁低压侧使用临时线作为互为备用电源。

7、乙方自备电源不得并入电网运行，如需同时使用甲方电源及自备电源时，电气结线应各自分开，不得并接，以保证用户负荷权取一个电源。

8、乙方电气值班人员，必须熟悉“双电源管理办法”的要求及调度协议内容、设备调度权限的划分、运行方式的有关规定，必须制定并严格执行现场倒闸操作规程。

9、乙方必须向甲方的调度部门和用电检查部门报送变(配)电值班人员名单;如值班人员有变动时，必须书面通知甲方的调度部门和用电检查部门。

10、乙方不得并列低压双路电源;用户有自备发电机者，其自备电源与电网连接处必须装设双投刀闸，不得使用电气闭锁。

11、乙方装设的自备发电机必须经甲方审核批准后方可投入运行，对未经审批私自投运自备发电机者，一经发现用电检查部门可责成其立即拆除接引线并按《供电营业规则》第100条第6款进行处理。

12、未经甲方用电检查人员同意，乙方不得改变自备发电机与供电系统的一、二次接线，不得向其他用户供电。

13、甲方用电检查部门对装有非并网自备发电机并持有《自备发电机使用许可证》的用户应单独建立台帐进行管理。

14、甲方和乙方分管的供电设施，除另有约定外，未经对方同意，不得操作或更动;如遇紧急情况(如危及电网和用电安全，或可能造成人身伤亡、设备损坏)而必须操作，事后应立即通知对方。

15、在电力供应暂时紧张时，或个别用户确因生产需要安装自备发电机组的，均按本规定办理;但电网供电正常后应立即拆除，改为单电源用电。

四、约定事项及违约责任

1、甲方对乙方自备电源的运行使用情况有权进行检查，对安全存在的隐患提出书面整改意见;乙方整改后，应及时进行验收。甲方不承担因乙方电气设备不合格引起的任何责任。

2、乙方对其所有的自备电源应定期进行检查、检修和试验，对可能危及受电线路廊道的树木、竹子及时进行修剪或砍伐，消除设备隐患，预防电气设备事故和误动作发生。

3、乙方未依照约定履行维护检查的义务，导致自备电源设备(含保护设施)带病运行，存在安全隐患的，甲方有权对用电方直接停止供电。

4、乙方误操作或其设备缺陷，使自备电源电力向甲方电网送电导致的设备和人身事故及一切经济损失全部由乙方承担。

5、乙方自备电源只能作为停电时的应急措施，自发自供，不得将自备电源的电力向自身以外供电;未经甲方同意，擅自供出电源的，按《供电营业规则》相关条款规定处理。

6、乙方未执行本协议或有关规定、管理不到位，给甲方或社会带来人身、设备损害，乙方必须承担全部法律责任。

五、争议的解决方式

甲乙双电方因履行本协议发生争议时应依本协议之原则协商解决;协商不成时，双方共同提请电力管理部门行政调解;调解不成时，双方可提起诉讼解决。

六、本协议效力及未尽事宜

1、本协议未尽事宜，按《电力法》、《电力供应与使用条例》、《供电营业规则》等有关法律、法规的规定办理;如遇国家法律、政策调整时，应按相应规定修改、补充本合同有关条款。

2、甲方、乙方任何一方欲修改、变更、解除协议时，按《供电营业规则》第94条办理;在修改、变更、解除协议的书面协议签定前，本协议继续有效。

3、本协议正本一式 份,甲方、乙方各执 份,自双方签字，加盖公章后生效。

4、本协议附件包括：

(1)供用电接线及产权分界示意图;

(2)双电源(自备电源)设备台帐表;

甲方：(签章) 乙方：(签章)

法定代表(负责)人： 法定代表(负责)人：

或其委托代理人： 或其委托代理人：

地址： 地址：

签订时间： 年 月 日 签订时间： 年 月 日

甲方(业主)： 身份证号：

乙方(施工方)： 身份证号：

甲、乙双方经友好洽谈和协商，甲方决定委托乙方进行居室装潢。为保证工程顺利进行，根据国家有关法律规定，特签订本合同，以便共同遵守。

第一条：工程概况

1、工程地址：

2、居室规格：室卫

3、建筑面积：平方米

4、承包方式： (包工包料、包清工、部分承包)

5、总价款： 元，大写(人民币)：

第二条：施工工期

1、总工期： 天

2、工程开工日期： 年 月 日

3、工程竣工日期： 年 月 日

4、如果因乙方原因而延迟完工，每日按工费的1%作为违约金罚款支付给甲方，直至工费扣完为止，如果因甲方原因而延迟完工，每延迟一日，以装潢工程价款中人工费的1%作为误工费支付给乙方元。

5、由甲方自行挑选的材料、设备，因质量不合格而影响工程质量和工期，其返工费由甲方承担，由于乙方施工原因造成质量事故，其返工费用由乙方承担，工期不变。

6、在施工中，因工程质量问题、双方意见不一而造成停工，均不按误工或延迟工期论处，双方应主动要求有关部门调解或仲裁部门协调、处理，尽快解决纠纷，以继续施工。

7、施工中如果因甲方原因要求重新返工的，或因甲方更改施工内容而延误工期的，均需签证，甲方须承担全部施工费用，如因乙方的原因造成返工，由乙方承担责任，工期不变。

8、施工中，甲方未经乙方同意，私自通知施工人员擅自更改施工内容所引起的质量问题和延误工期，甲方自负责任。

第三条：工程价格

以附表《装修工程价格表》所定的价格为准。

第四条：质量要求

1、工程使用主要材料的品种、规格、名称、经双方认可。

2、工程验收标准，双方同意参照市地方标准DB31/T30-1999《住宅装饰装修验收标准》规定。

3、施工中，甲方如有特殊施工项目或特殊质量要求，双方应确认，增加的费用，应另签订补充合同。

4、质量检查监督部门：市家居装饰专业委员会。

5、凡由甲方自行采购的材料、设备，产品质量由甲方自负;施工质量由乙方负责。

6、甲方如自聘工程监理，须在工程开工前通知乙方，以便于工作衔接。

第五条：甲方义务

1、甲方必须提供经物业管理部门认可的房屋平面图及水、电、气线路图，或由甲方提供房屋平面图及水、电、气线路图，并向乙方进行现场交底。

2、二次装饰工程，应全部腾空或部分腾空房屋，清除影响施工的障碍物。对只能部分腾空

的房屋中所滞留的家具、陈设物等，须采取必要的保护措施，均需与乙方办理手续和承担费用。

3、如确实需要拆、改原建筑物结构或设备、管线，应向所在地房管部门办理手续，并承担有关费用。施工中如需临时使用公用部位，应向邻里打好招呼。

第六条：乙方义务

1、乙方应主动出示企业营业执照。

2、指派 (姓名)为乙方工地代表，负责合同履行，并按合同要求组织施工，保质保量地按期完成施工任务。

3、严格履行合同，实行信誉工期，如果因延迟完工，如脱料、窝工或借故诱使甲方垫资，举查后均按违约处。

4、在装潢施工范围内承担保修责任，保修期自工程竣工甲方验收入合格之日算起，为12个月。

第七条：材料供应

1、乙方须严格按照国家有关价格条例规定，对本合同中所用材料一律实行明码标价。甲方所提供的材料均应用于本合同规定的装潢工程，非经甲方同意，不得挪作他用。乙方如挪作他用，应按挪用材料的双倍价款补偿给甲方。

2、乙方提供的材料、设备如不符合质量要求，或规格有差异，应禁止使用。如已使用，对工程造成的损失均由乙方负责。

3、甲方负责采购供应的材料、设备，并应按时供应到现场。如延期到达，施工期顺延，并按延误工期处罚。按甲方提供的材料合计金额的10%作为管理费支付给乙方。由乙方负责保管，由于保管不当而造成损失，由乙方负责赔偿。

第八条：工程验收

1、工程质量验收，除隐蔽工程需分段验收外，待工程全部结束后，乙方组织甲方进行竣工验收。双方办理工程结算和移交手续。

2、乙方通知甲方进行工序验收及竣工验收后，甲方应在三天内前来验收，逾期视为甲方自动放弃权利并视为验收合格，如有问题，甲方自负责任。甲方自行搬进入住，视为验收合格。

3、甲方如不能在乙方指定时限内前来验收，应及时通知乙方，另定日期。但甲方应承认工序或工程的竣工日期，并承担乙方的看管费和相关费用。

第九条：付款方式

1、合同一经签订，甲方即应付全款30%作为订金;当工期进度过半(年月日)，甲方即第二次付施工工费的50%;剩余20%尾款待甲方对工程竣工验收后结算。

2、工程施工中如有项目增减或需要变动，双方应签订补充合同，并由乙方负责开具施工变更报告，通知施工工地负责人。增减项目的价款，当场结清。

第十条：违约责任

合同生效后，在合同履行期间，擅自解除合同方，应按合同总金额5%作为违约金付给对方。因擅自解除合同，使对方造成的实际损失超过违约金的，应进行补偿。

第十一条：争议解决

1、本合同履行期间，双方如发生争议，在不影响工程进度的前提下，双方应协商解决。或凭本合同和乙方开具的统一发票向市室内装饰行业协会家庭装潢专业委员会投诉，请求解决。

2、当事人不愿通过协商、调解解决，或协商、调解解决不成时，可以按照本合同约定向—仲裁委员会申请仲裁;--人民法院提起诉讼。

第十二条：合同的变更和终止

1、合同经双方签字生效后，双方必需严格遵守。任何一方需变更合同的内容，应经双方协商一致后重新签订补充协议。如需终止合同，提出终止合同的一方要以书面形式提出，应按合同总价款的10%交付违约金，并办理终止合同手续。

2、施工过程中任何一方提出终止合同，须向另一方以书面形式提出，经双方同意办理清算手续，订立终止合同协议后，可视为本合同解除

第十三条：合同生效

1、本合同和合同附件向双方盖章，签字后生效。

2、补充合同与本合同具有同等的法律效力。

3、本合同一式贰份，甲乙双方各执壹份。

甲方：(签章) 乙方：(签章)

住所地址： 企业地址：

电话号码： 电话号码：

年月 日 年月 日

负责建筑施工工程项目的人员管理、安全施工和技术质量监管工作。

1.认真贯彻、执行国家的政策、法规和公司各项规章制度;全面负责项目工程进场前人力财力的组织工作和入场后施工现场的管理工作;主持项目部工作。

2.全面完成公司下达给工程项目的各项考核指标，确保工程质量、安全、工期的实现，认真履行施工合同。

3.参加项目施工组织设计的编制和工程预结算的会审，坚持项目过程精品，动态管理，标价分离，严格奖罚。

4.负责主持编制和组织实施施工合同内容的施工进度计划，按时向公司报送工程实物完成量，按时向业主收取工程进度款。

5.严格按公司质量管理体系工作和质量方针要求实现工程质量目标，负责组织对施工过程中的各种技术、质量、安全、成本等相关工作实施情况的考核。

6.合理统筹安排好项目工程的物资、劳动力、施工技术、设备、后勤、行政、社会治安综合治理、文明施工等的管理工作。

7.负责完成公司经理授权处理的事宜，定期或不定期将工程现状上报公司，并执行公司的指令。

8.负责与政府相关部门、业主、监理、分包单位的协调工作。

9.定期组织项目部各专业人员进行业务培训，开展“QC”小组活动。

10.负责对本项目工程完工后的工作总结。

图书馆系统技术支持服务合同范本

一、协议双方

甲方：_________

乙方：_________

二、协议内容

经甲乙双方友好协商，应甲方要求乙方提供以下服务：

1.协助甲方进行图书馆系统维护并且建立系统维护记录。

2.上门进行软件的维护，及时发现问题并解决问题。

3.根据甲方的需要，修改系统的配置文件、帐户、打印输出格式、统计报表输出格式等。

4.根据甲方软件使用情况及设备情况制定科学的数据备份方案和方法，并协助甲方进行日常数据备份。

5.协助同一版本软件的升级工作。

6.根据甲方的要求，制作图书馆的主页。

7.乙方负责甲方操作员现场培训。

8.甲方免费参加乙方在_________或_________组织的操作员培训。

三、费用

其一年技术支持服务费用为所购软件的_________%。

四、服务方式

上门及电话服务，二十四小时内响应。

五、服务期限

自_________年_________月_________日至_________年_________月_________日，有效期为_________年。

六、付款方式

1.自签约之日起，甲方向乙方支付技术支持服务费。

2.乙方收到用户支付的技术支持服务费后，即开始为甲方提供服务。

七、违约责任

按经济法，合同双方友好协商解决。

八、本协议一式二份，有效期为_________年，甲乙双方各执一份，自签订之日起即生效，双方均应严格遵守。

甲方(盖章)：_________ 乙方(盖章)：_________

代表(签字)：_________ 代表(签字)：_________

_________年____月____日 _________年____月____日

签订地点：_________ 签订地点：_________

(1)负责组织编制工程施工组织设计、分项工程施工方案，以及新技术、新工艺、新材料、新设备的应用方案，报公司总工程师审核批准后指导项目部组织实施;

(2)负责制定重点分项、重点部位的施工方案或施工方法;

(3)依据建筑施工合同确定的工程质量目标，审核批准项目部编制的工程质量目标计划大纲;

(4)负责解决施工中遇到的重大疑难问题;

(5)负责组织较重大质量事故的调查处理和整改工作;

(6)负责与设计单位、监理单位共同研究解决重点或关键技术问题;

(7)主持编制审核工程施工组织设计(分包)、施工方案(分包)、工序程序等文件，报公司审批后组织实施;

(7)完成领导交办的其他工作。

(8)组织施工图纸会审、提前发现图纸中的问题，及时与设计、监理联系解决，超前解决施工中的技术问题。

(9)负责项目部工程质量管理工作。组织质量体系文件的落实;执行工程质量检验评定标准;组织编制工程质量目标计划，对工程质量实施有效控制 ，确保质量目标的实现。

(10)负责签发设计变更洽商及所有应由技术负责人签审的工程技术资料文件。

(11)负责组织新技术、新工艺、新材料、新设备的推广应用及技术革新、技术改造工作。

(12)负责组织制定降低工程成本的技术措施，并组织实施。

(13)负责指导工程资料的收集、整理、归档工作;;指导工程有关试验，组织编写工程竣工总结、竣工报告;组织绘制竣工图;组织办理竣工资料文件的移交工作。

(14)完成项目经理交办的其他工作。

契约号：_____

日期：_____

签约地点：____

甲方：__________________ 乙方：__________________

地址：__________________ 地址：__________________

电话：__________________ 电话：__________________

传真：__________________ 传真：__________________

联系人：_________________ 联系人：_________________

鉴于甲方希望乙方提供，乙方愿意向甲方提供有关公司内部信息管理平台的技术服务和其它相关技术服务(以下合并称为“技术服务”)经友好协商，甲乙双方就上述技术服务事宜达成如下条款：

一、技术服务的内容、方式和要求

1、服务内容：

乙方派出合格技术人员为甲方提供有关计算机及网络的系统维护、技术支持和咨询服务。

2、方式：

甲方在需要乙方提供技术服务时，邮件或电话通知乙方mis部门主管，或者乙方认为有必要对甲方的系统进行维护并经甲方主管同意时，乙方应及时派出合格的工程师提供所要求的技术服务。

3、工作单：

服务结束后，乙方工程师填写工作单，写明工作内容、工作过程、完成情况以及实际工作时间，并经甲方主管签字，由乙方mis部门保存。工作单是有关服务费用结算的依据。

二、工作条件和协作事宜

1、甲方应为乙方技术服务提供必要的工作场所和工具;

2、乙方人员在进行系统维护时，必须确保甲方系统中的信息安全，未经甲方同意不得擅自删除和转移甲方系统中的信息，并为其保密。

三、报酬及其支付方式

1、甲方对乙方在本契约的有效期内所提供的服务按rmb____/人工作日(或rmb____/人工作日)的费用标准支付给乙方。

2、支付方式：

每月月底(非工作日则顺延至下一个工作日)按工作单的工作时间(每次工作时间不满一小时的按一工作小时计算，8个工作小时折算为一工作日)，甲方为乙方结算一次。由乙方开出服务发票，甲方按发票上的金额和指定银行以支票或电汇方式进行支付。

四、契约有效期

契约自____年____月____日起有效，至____年____月____日止。

五、违约责任

(一)甲方的违约责任

若甲方未按契约规定的时间如期向乙方支付服务费用，逾期____天至____天(含十天)，应支付相当于契约报酬总额的____%的违约金;逾期____天以上，应视为严重违约，除支付相当于契约报酬总额的____%的违约金外，并对由此而造成的一切后果承担全部责任。

(二)乙方的违约责任

若乙方所提供的技术服务在质量保证和信息安全方面不能满足甲方要求，经甲方两次指出仍无改进的，甲方有权解除契约。

六、争议解决

如果执行本契约发生争议，甲乙双方应友好协商解决。若协商不成，双方同意将该等争议提交北京市仲裁委员会，按照申请仲裁时该会现行有效的仲裁规则进行仲裁。仲裁裁决是终局的，对双方均有约束力。除仲裁机构另有决定外，仲裁费用和其它相关费用由败诉方承担。

七、本契约经甲乙双方代表签字并加盖公章后生效。

八、本契约正本一式两份，甲乙双方各执一份，具有同等法律效力。

甲方：__________________ 乙方：__________________

代表人：________________ 代表人：________________

_____年__月__日 _____年__月__日

物业管理公司实习报告范文

物业管理公司实习报告

本文由第一范文网小编推荐给大家参考阅读！

本人于XX年7月至XX年12月在广东省东莞市中信物业管理有限公司实习，其中秩序维护员4个月，客服2个月。短短的半年一晃眼便过去了，在这期间有欢笑、也有汗水。喜的是作为中信的一员，与公司同甘苦、共患难，在工作中学到了许多有关物业管理的知识和实践操让我对物业管理有了更加全面透彻的了解；苦的是我也在工作中经历了大大小小的难以处理的事情和与公司一线员工一起工作，体会到了作为秩序维护员的那份艰辛与劳累。

忘不了的是将要实习工作、离开集体、离开父母、离开同学的那份难以割舍和留恋的情怀；忘不了的是与同学告别，相互拥抱、流泪、挥手告别的场面；忘不了的是我终于正式迈入社会、独立生活、将要成就属于自己的那份梦想激动的心情…

XX年7月1日，经过一天一夜的长途跋涉终于到达了东莞，这个让我渴望而又懵懂的城市，大家最初那份将要踏向异乡的兴奋心情也随着漫长的列车颠簸而渐渐消退。可当大家下火车的那一刻，看到人力资源部古经理热情的帮我们提行李、发面包、递水，我们的疲惫转眼又一消而退，被这个公司的热情而打动。我在心里默默的祈祷，我一定行！在公司总部，经过一天的安排和分配，工作，将要开始了…

XX年7月2号经过一天的休息和调整后我被分到阳光管理处暂行两个月的实习工作。很快，我们便以一个积极、热情的心态进入了工作状态。短短的两个月，我主动了解我管理处职能范围、机构设置、人员编制等基本情况，并且严格遵守我处的各项规章制度。其中我主要接手了vip客户接待这一工作，负责对于维修单的回访验证及各项资料诸如物品放行条、保修、巡查维修记录表、日常巡查签到表、清洁卫生、绿化检查表等的整理。在工作中遇到了种种困难，如在给业主打电话时经常会遇到业主大发牢骚，而我，也在慢慢的累积经验，学会了倾听，学会用语言耐心的向业主解释，用我的真诚去认真的对待每一位客户。在客服前台，我更学会了用微笑面对客户，耐心的向他们解释管理处的一些规定是为业主着想，帮助业主开物品放行条、给住户卡授权、办理车卡等等。物业管理公司实习报告

记得住的便是在暴雨中和同事帮业主把小孩抱到避雨处得到业主谢意的那份开心；记得住的便是管理处内审时大家一同整理资料的那些吃泡面加班的日子；记得住的便是给我们培训、和我们畅谈社会、畅谈工作、畅谈理想的那些老同事；更忘不了的是参加公司竞聘，一轮笔试、二轮机试、第三轮面试落榜的那份难过和苦涩…客服部，这个给我造梦的部门给我留下了太多值得回忆的梦…

可实习毕竟不只在一个部门，怀着百分之一百二的不愿意，我和其他几个同学来到了保安交通部进行实习。时间，XX年9月1日。在保安交通部，是第一次真真正正的和中信的一线员工一起工作，多少个日日夜夜，多少次不断的抱怨，多少汗水，都是我们在保安部的点点滴滴。虽然，这个部门人员繁杂，这个部门工作艰辛，这个部门充满钩心与斗角，但是我们的工作还要进行，我们的实习还要进行，我们，还是中信的一员。在这个部门，与一线员工一起工作、吃饭、休息，渐渐的，我开始融入这个让人纠结的复杂集体。

合同号：_____________

由甲方：_____________

地址：_____________

电话：_____________

传真：_____________

邮编：_____________

和乙方：_____________

地址：_____________

电话：_____________

传真：_____________

邮编：_____________

甲、乙双方就乙方向甲方提供技术服务的各项事宜，依照中华人民共和国相关法律法规及工作规范，本着平等互利的原则，签订协议如下：

一、工作内容

乙方按本协议为甲方提供技术服务，在甲方的配合下，指导甲方完成相关文件的编写，人员的培训，指导甲方。

二、服务范围

三、服务费用及支付方式

1服务费用：___________________________元(￥______________元)

2付款方式：甲方应于________年____月____日前一次性支付给乙方。

四、双方的责任和权利

1、乙方承担的咨询服务包括与上述服务相关的所有工作;

2、乙方负责指导甲方服务过程所需资料收集以及提供适当的培训;

3、乙方派出的技术服务人员应严格执行国家有关法律和工作纪律，甲方若在接受服务过程中对其工作不满意，可向乙方提出投诉或异议，乙方将酌情调整;

4、乙方技术服务人员负责拟订咨询工作计划，并须告之甲方，服务工作计划执行过程中的任何调整应及时以书面形式通知对方。收到通知的一方如在三日内无书面异议，视为认可;

5、乙方对甲方工作而涉及的商业秘密承担保密责任;

6、甲方提供乙方技术服务人员在服务期间的交通、食宿条件及相关资源;

7、甲方应指定专人作为联络员配合乙方技术服务人员的工作。

五、违约责任

1、甲乙双方任何一方违反本合同或擅自提前终止本合同均应承担违约责任;

2、违约方除承担本合同规定的全部咨询服务费外，还应支付给守约方违约(按合同金额的25%)以弥补给其造成的损失;

3、违约方必须明确责任后一个月内结清所有违约费用，否则，每月按总金额的1.5%交付滞纳金。

六、争议解决法律适用

1、本合同受中华人民共和国法律约束，有关本合同的效力、解释和履行过程中的一切纠纷均由甲方所在地的中华人民共和国法院管辖处理;

2、双方所达成的任何其它一致均构成本合同不可或缺的一部分，与本合同具有同等的法律效力，其中若有冲突之处，以最后达成的为准。

七、合同文本、文字及生效

1本协议自双方代表签字并加盖公章之后生效;

2本协议一式贰份，双各方执壹份。

甲方代表______________(盖章)乙方代表______________(盖章)

________年____月____日________年____月____日

技术转让合同范本

4.3.3 甲方收到乙方下列单据并审查无误后的＿＿＿＿天内向乙方支付提成费； （a）即期汇票正、副本各一份。 （b）商业发票正本一份，副本三份。 （c）该年提成费计算书一式四份。

4.3.4 在合同期满年度内，甲方在合同终止后＿＿＿＿天内将提交一份最后销售合同产品数量的报告，以便乙方计算提成费。

4.4 按本合同规定，如乙方向甲方支付罚款或赔偿时，甲方有权从上述任何一次支付中扣除。 第五章 技术资料支付

5.1 乙方应按本合同附件二的规定向甲方提供技术资料。

5.2 乙方应在＿＿＿＿机场或车站交付技术资料。＿＿＿＿机场或车站的印戳日期为技术资料的有效支付日期。甲方应在收到资料两周后，确认资料收悉。

5.3 第一阶段产品的技术资料、样机、铸件和备件：

5.3.1 在合同生效后的＿＿＿＿周内，乙方必须发出一套蓝图，一套二底图和一套标准。可以分批交货。 5.3.2 在合同生效后的＿＿＿＿周内，乙方必须发出与第一阶段合同产品有关的全部技术资料、样机、铸件和备件。

5.4 第二阶段产品的技术资料和样机：

5.4.1 第二阶段开始日期后的＿＿＿＿周内，乙方必须发出与第二阶段产品有关的一套蓝图，一套二底图和一套标准。可以分期交货。

5.4.2 第二阶段开始后的＿＿＿＿周内，乙方必须尽快发出与第二阶段合同产品有关的全部技术资料和样机、铸件和备料。

5.5 在每批技术资料或样机、铸件和备件发运后的＿＿＿＿小时内，乙方应将空运提单号、空运提单日期、资料编号、合同号、件数和重量电告甲方。同时乙方应以航空信将下列单据寄给甲方： （a）空运提单正本一份，副本二份。 （b）所发运技术资料、样机、铸件和备件的详细清单一式二份。

5.6 若乙方提供的技术资料或样机、铸件和备件在运输途中遗失或损坏，乙方在收到甲方关于遗失或损坏的书面通知书后，应尽快不迟于＿＿＿＿个月内免费补寄或重寄给甲方。

5.7 交付技术资料应具有适于长途运输、多次搬运、防雨、防潮的坚固包装。 在每件包装箱的内部与外表，都应以英文标明下列内容。 （a）合同号 （b）运输标记 （c）收货人 （d）技术资料目的地 （e）重量（公斤） （f）样机、铸件和备件目的地

5.8 每箱内应附有详细装箱单一式四份。 第六章 技术资料的改进和修改 6.1 为了适应中国的设计标准、材料、工艺装备和其它生产条件，在不改变乙方基本设计的条件下，甲方有权对乙方的技术资料进行修改和变动。甲方必须将这些修改和变动通知乙方。乙方有责任在培训或技术指导时协助甲方修改技术资料，详见附件三和附件四。

6.2 甲方必须在型号后加注尾标，以示区别那些影响形状，配合或功能的修改，并通知乙方。 6.3 合同有效期内，双方在合同规定的范围内的任何改进和发展，都应相互免费将改进、发展的技术资料提交给对方。

6.4 改进和发展的技术，所有权属改进、发展的一方。

共7页，当前第3页1234567

职责：

1.负责新产品、OEM产品工厂阶段的相关项目管理及协调等工作;

2.主导新机型、OEM产品样机评审,试产前培训,上线试产,试产总结,量产导入等相关事宜;

3.负责新产品、OEM产品技术资料,测试标准的确认及技术支持和培训;

4.主导新产品、OEM产品的重大问题的处理及改善(如SMT，PCBA，组装、供应商等);

任职要求：

1.本科学历，电子或管理专业，英文6级;

2.5年以上电子企业项目管理工作经验，设对工控机、通讯设备(非手机)特别在大型EMS企业工作经历;

技术出口合同范本

Contract for Equipment Sales and Technology Licensing

Contract No. ____________________

This Contract (hereinafter referred to as the “Contract”) is made and entered into as of ________ (the date of signature ) in ________ (the place of signature) through friendly negotiation by and between _____________, a company incorporated and existing under the laws of ____________ with its registered address at ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­_________________________________, and with its principal place of business at _________________________________ (hereinafter referred to as the “Buyer”), and ____________________, a company incorporated and existing under the laws of the People’s Republic of China with its registered address at ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­_________________________________, and with its principal place of business at _________________________________(hereinafter referred to as the “Seller”).

Whereas, the Buyer desires to engage the Seller to provide the Equipment, related design, Technical Documentation, Technical Service and Technical Training and to obtain from the Seller a license of Patent and/or Know-how in relation to the Erection, Test Run, Commissioning, Performance Test，operation and maintenance for the Equipment, as well as manufacture of the Contract Products. Now it is hereby mutually agreed as follows:

Article 1 Definitions

1.1 “Acceptance ”means the Buyer accepted the Equipment in accordance with Article 11.5.

1.2 “Commissioning” means the operation of the Equipment in accordance with Article 11.4 for the purpose of carrying out Performance Test.

1.3 “Contract” means this Contract signed by and between the Buyer and the Seller, including Appendices attached which shall form an integral part of this Contract.

1.4 “Contract Products” refers to all types of the products manufactured with Patent and/or Know-how under the Contract, details of which are specified in Appendix 1.

1.5 “Destination Airport” refers to _____________Airport.

1.6 “Effective Date of the Contract” means the date when the Contract enters into force upon fulfillment of all the conditions stated in Article 18.1.

1.7 “Equipment” means the equipment, machinery, instruments, spare parts and materials supplied by the Seller as listed in Appendix 3.

1.8 “Erection” means placing the Equipment to the positions according to the design drawings, and connecting it with relevant equipment and utilities.

1.9 “Improvement” refers to new findings and/or modifications made in the validity period of the Contract by either party on Patent and/or Know-how in the form of new designs, formulas, recipes, ingredients, indices, parameters, calculations, or any other indicators.

1.10 “Job Site” means the site where the Equipment shall be located and/or erected, namely ____.

1.11 “Know-how” refers to any valuable technical knowledge, data, indices, drawings, designs and other technical information, concerning the Erection, Test Run, Commissioning, Performance Test，operation and maintenance for the Equipment as well as manufacture of the Contract Products, developed and owned or legally acquired and possessed by the Seller and disclosed to the Buyer by the Seller, which is unknown to either public or the Buyer before the Date of Effectiveness of this Contract, and for which appropriate protection measures have been taken by the Seller for keeping Know-how in secrecy. The specific description of Know-how is set forth in Appendix 3.

1.12 “Last Shipment” means the shipment with which the accumulated invoice value of shipped goods has reached ____ ( ) percent of the total Equipment price.

1.13 “Patent” refers to any and all of the effective patent rights possessed by the Seller and licensed to the Buyer under the Contract in connection with the Erection, Test Run, Commissioning, Performance Test,operation and maintenance for the Equipment, as well as manufacture of the Contract Products, the No. and list of which are set forth in Appendix 3.

1.14 “Performance Test” means the tests for examining whether the Equipment is able to meet guarantee figures specified in Appendix 1.

1.15 “Technical Documentation” means the technical indices and data, specifications, drawings, processes, technical and quality standards, and other documents carrying the descriptions and explanations of Patent, Know-how and other technical information, in connection with the Erection, Test Run, Commissioning, Performance Test，operation and maintenance for the Equipment, as well as manufacture of the Contract Products, to be provided by the Seller as listed in Appendix 4.

1.16 “Technical Service” means the technical instruction, assistance and guidance rendered by the Seller as per Appendix 6.

1.17 “Technical Training ” means the training rendered by the Seller as per Appendix 7.

1.18 “Test Run” means the initial run of a single machine or the whole system of the Equipment without materials.

1.19 “Warranty Period” means the period of the warranty given by the Seller as specified in Article 12.2, during which the Seller is responsible for the defects of the Equipment as per Article 12.

Article 2 Scope of the Contract

2.1 The Seller’s Obligation

2.1.1 The Seller shall supply the Equipment, provide the design, Technical Documentation, and conduct the Technical Service and Technical Training, and grant the Buyer a right to use the Patent and/or Know-how as set forth in the Contract.

2.1.2 The Seller shall supply the Equipment which is listed in Appendix 3, the specification is detailed in Appendix 1.

2.1.3 The Seller shall provide design in accordance with Appendix 5, and submit to the Buyer the Technical Documentation listed in Appendix 4.

2.1.4 The Seller shall conduct the Technical Services at the Job Site as per Appendix 6.

2.1.5 The Seller shall conduct the Technical Training as per Appendix 7.

2.2 The Buyer’s Obligation

2.2.1 The Buyer shall at his own costs and expenses, provide the Seller with all information and data concerning the design as per Appendix 2. The Buyer shall ensure the completeness, correctness and accuracy of all such information and data.

2.2.2 The Buyer shall at his own costs and expenses, obtain all necessary import permits, undertake customs clearance, take delivery of the Equipment to be supplied by the Seller and transport them to the Job Site in time.

2.2.3 The Buyer shall at his own costs and expenses, perform all the civil works, construction, Erection, Test Run， Commissioning and Performance Test in accordance with the Technical Documentation under the Technical Services rendered by the Seller as per Appendix 6.

2.2.4 The Buyer shall at his own costs and expenses, supply all the equipments, spare parts and facilities required, except for the Equipment supplied by the Seller as per Appendix 3.

2.2.5 The Buyer shall at his own costs and expenses, provide the qualified and appropriate technical personnel, labor, tools, utilities and the Job Site in time for Erection, Test Run, Commissioning, and Performance Test as specified in Appendix 2.

2.2.6 The Buyer shall at his own costs and expenses, perform necessary administration and security guard at the Job Site.

Article 3 Grant of License

3.1 The Seller agrees to grant to the Buyer and the Buyer agrees to obtain from the Seller a license to manufacture the Contract Products as well as to conduct Erection, Test Run, Commissioning, Performance Test, operation and maintenance for the Equipment with Patent and/or Know-how as well as to use and sell the Contract Products. The name, model, specification, and technical data of the Contract Products are detailed in Appendix 1. The Buyer shall not make use of Patent and/or Know-how for any purposes other than those stipulated in the Contract without prior written approval from the Seller. The annual output of the Contract Products manufactured by the Buyer shall in no case exceed _______________.

3.2 (Option 1) The license granted under the Contract shall be an exclusive license. The Seller shall not retain its right to grant the licenses to any third parties, or to explore Patent and/or Know-how as well as to sell the Contract Products by itself within the territory specified in Article 3.4.

(Option 2) The license granted under the Contract shall be a non-exclusive license. The Seller shall retain its right to grant the licenses to any third parties, and to explore Patent and/or Know-how as well as to sell the Contract Products by itself within the territory specified in Article 3.4.

3.3 The license granted under the Contract shall be a non-transferable and non-sublicensing license, under which the Buyer shall neither be entitled to transfer nor grant sub-license to any third party without prior written approval from the Seller.

3.4 Territory

3.4.1 The Seller agrees to grant the license to the Buyer only within the territory of _________________ (country or region). The Buyer shall not explore Patent and/or Know-how in any place other than the Job Site without previous written consent of the Seller.

3.4.2 The Seller agrees to grant a license to the Buyer to use and sell the Contract Products only within the territory of ________________________ (Country or region). In case the Buyer fails to perform its obligations under this Clause, all the actual losses and damages thus incurred to the Seller shall be borne by the Buyer, and the Seller shall have the right to terminate the Contract without prejudice to any remedies specified in the Contract.

Article 4 Price

4.1 The Buyer agrees to pay the total Contract price, Technical Training and Technical Service fee to the Seller.

4.2 The total Contract price, including price of the Equipment, design, Technical Documentation and a license fee in a fixed amount, shall be __________(say _______________________ only).

The breakdown price is as follows:

The price for Equipment is __________(say _______________________ only).

Fee for design is __________(say _______________________ only).

Fee for Technical Documentations is __________(say _______________________ only).

License fee is __________________(Say: _________________ only)

4.2.1 The total Contract price for the Equipment is for delivery CIF_____ Port, and the Technical Documentations is for delivery CIP (by air) ______ Airport. CIF and CIP term shall be interpreted in accordance with INCOTERMS 2019, issued by the INTERNATIONAL CHAMBER OF COMMERCE (ICC).

4.2.2 The total Contract price includes the price for spare parts listed in Appendix 3. However, the total Contract price does not cover the supply of any other spare parts. At the Buyer’s request, the Seller may provide with any other spare parts. A separate agreement shall be signed between the parties.

4.2.3 The above price is fixed and firm.

4.3 The total Contract price does not cover the Technical Service fee and Technical Training fee specified in Appendix 6,7.

4.4 The total Contract price as well as the Technical Training and Technical Service fee shall not be regarded or in any way be explained or interpreted as covering any of the custom duties, taxes, or charges, fees, and expenses unless expressly listed in the Contract.

Article 5 Payment

5.1 Down Payment

Within ____ ( ) days after signing the Contract, the Buyer shall pay ____ ( ) percent of the total Contract price amounting ____ by T/T to the Seller.

5.2 [Option One: Payment by Sight L/C]

The balance of the total Contract price amounting ___ ( says ___ only ) shall be paid by an irrevocable Letter of Credit at sight, issued within ___ ( ) days after signing the Contract by a reputable bank in ___ acceptable to the Seller in favor of the Seller. The Letter of Credit shall be available upon the presentation of the following documents till ______(specific expiration date or a specific circumstance for the expiration of the Letter of Credit).

5.2.1 ____ ( ) percent of the total Contract price amounting ____ (say ___ only) shall be paid by the Buyer to the Seller within _______ days after the following documents have been submitted by the Seller:

(a) Bill of Lading in one (1) original and ___ ( ) copies;

(b) Commercial Invoice in one (1) original and ___ ( ) copies;

(c) Packing list in one (1) original and ___ ( ) copies;

(d) Certificate of Origin in one (1) original and ___ ( ) copies;

(e) Insurance Policy in one (1) original and ___ ( ) copies;

5.2.2 ____ ( ) percent of the total Contract price amounting ____ (say ___ only) shall be paid by the Buyer to the Seller within _______ days after the following documents have been submitted by the Seller:

(a) One (1) copy of the Acceptance Certificate signed by the Buyer as per Article 11.5, or the Seller’s written statement specifying the lapse of more than seven (7) days after the Seller’s notice requesting the Buyer to issue the Acceptance Certificate in accordance with Article 11.5;

(b)One ( 1 ) copy of commercial invoice.

5.2.3 ____ ( ) percent of the total Contract price amounting ____ (say ___ only) shall be paid by the Buyer to the Seller within _______ days after the following documents have been submitted by the Seller:

a) One (1) original Letter of Retention Guarantee in the form of Appendix 10;

b) One (1) copy of Commercial Invoice.

5.2 [Option Two: Payment under a L/G]

The balance of the total Contract price amounting ___ (say ___ only ), plus interest for deferred payment in the amount of ___ (say ___ only ), totaling ___ (say ___ only ) as detailed in Appendix 12 shall be paid by the Buyer by installments as specified in Appendix 12 and backed by an irrevocable Letter of Guarantee in favor of the Seller as per the Appendix 11, issued within ___ ( ) days after signing the Contract by the reputable bank in ____ acceptable to the Seller.

5.3 All the banking charges incurred in the Seller’s bank shall be borne by the Seller while those incurred outside the Seller’s bank shall be borne by the Buyer.

Article 6 Delivery of Equipment and Technical Documentation

6.1 The Delivery of the Equipment

6.1.1 The delivery of the Equipment listed in Appendix 3 shall be completed within ____ ( ) months from the Effective Date of the Contract.

6.1.2 Within ____ ( ) months after the Effective Date of the Contract, the Seller shall send to the Buyer a preliminary delivery schedule by fax.

Not later than ____ ( ) days before the first shipment, the Seller shall submit to the Buyer the final delivery schedule in three (3) copies indicating Contract number, dispatch number, name of the Equipment, quantity, approximate dimensions, volume of each package and time of each shipment.

6.1.3 The port of shipment is ____, while the port of destination is ____.

6.1.4 Advance shipment, partial shipment and transshipment are allowed, however, the Seller shall inform the Buyer thirty (30) days before such shipment.

6.1.5 The date of Bill of Lading for each shipment shall be considered as the actual delivery date.

6.1.6 The Seller shall notify the Buyer by fax of the following within five (5) working days after each shipment is effected:

(a) Contract number

(b) Name of the vessel and loading port

(c) Name of the Equipment shipped

(d) Number and date of Bill of Lading

(e) Total volume

(f) Total gross and net weight

(g) Total number of packages/cases

6.1.7 The Seller shall airmail the following documents in duplicate to the Buyer:

(a) Bill of Lading

(b) Commercial Invoice

(c) Packing List

(d) Certificate of Origin

(e) Insurance Policy.

6.2 The Late Delivery of the Equipment

6.2.1 If the Seller fails to deliver the Equipment in accordance with the final delivery schedule, the Seller shall pay to the Buyer liquidated damages for such delay at the following rates:

(a) From the first week to the fourth week, the liquidated damages shall be

____ ( ) percent of the value of the delayed portion of the Equipment per

week

(b) From the fifth week to the eighth week, the liquidated damages shall be

____ ( ) percent of the value of the delayed portion of the Equipment per week

(c) From the ninth week, the liquidated damages shall be ____ ( ) percent of

the value of the delayed portion of the Equipment per week

6.2.2 The fractions of four days or more shall be counted as one week and fractions of less than four days shall be omitted. The total aggregate amount of the liquidated damages shall not exceed ____ ( ) percent of the value of the delayed portion Equipment.

6.2.3 The Seller shall be released from the liability to the Buyer whatsoever in respect of the late delivery after his payment of liquidated damages in accordance with Article 6.2. Notwithstanding the Seller’s payment of the liquidated damages for the late delivery Equipment, the Seller shall not be released from his obligation to deliver the Equipment.

6.3 The Delivery of the Technical Documentation

6.3.1 The Technical Documentation listed in Appendix 4 shall be delivered CIP ____airport by air within ____ ( ) months after the Effective Date of the Contract.

6.3.2 The date of airway bill shall be regarded as the actual delivery date of the Technical Documentation.

6.3.3 Within ____ ( ) working days after sending each lot of the Technical Documentation, the Seller shall inform the Buyer of the Contract number, item number, number and date of airway bill and the flight.

6.3.4 In case of shortage, loss of or damage to the Technical Documentation due to the Seller’s reason, the Seller shall make supplement to the Buyer within ____ ( ) days after receiving the Buyer’s written notification without any further charge.

Article 7 Packing and Marking

7.1 The Equipment shall be packed to withstand long distance transportation, multiple handling.

7.2 The Seller shall mark the following on two opposite sides of each package with indelible painted English words:

(a) Destination

(b) Consignee

(c) Contract number

(d) Shipping mark

(e) Gross/net weight (kg)

(f) Case/ bale number

(g) Dimensions: L x W x H (cm)

7.3 Each package shall contain one (1) copy of packing list.

7.4 The Seller shall mark on the package, if necessary, “Handle with Care", “Right Side Up", “Fragile" or other indicative marks according to the characteristics and feature of the goods as well as different requirement for transportation, loading and unloading of the goods.

7.5 If the goods weigh three (3) or more than three (3) metric tons, gravity, hoisting position and illustrative marks shall be marked so as to facilitate loading, unloading and handing.

(a) Destination

(b) Consignee

(c) Contract number

(d) Gross/net weight (kg)

(e) Item number

(f) Dimensions: L x W x H (cm)

Article 8 Technical Service and Technical Training

8.1 The Seller shall dispatch technical personnel to Job Site to render Technical Service in accordance with Contract according to a time schedule agreed upon between both parties. The number, specialty, rank, treatment of the personnel, and payment as well as the contents, and requirements of Technical Service are specified in Appendix 6.

8.2 The Buyer shall have the right to send its technical personnel to the relevant factory selected by the Seller for training. The number, speciality, treatment of the personnel, and payment as well as the contents, time schedule, and requirement of training, are specified in Appendix 7.

8.3 Either party shall provide assistance to the other party’s technical personnel in their application for visa, working permit, and/or other necessary formalities for rendering Technical Service or training under the Contract in the other party’s factory.

8.4 Either Party’s technical personnel shall abide by the laws of the other party’s country and the regulations of the other party during their stay in the other party’s country.

Article 9 Standards and Inspection

9.1 The Seller shall carry out the design, manufacture, inspection and test of the Equipment according to the existing standards of the People’s Republic of China, namely GB.

9.2 The Seller or the manufacturer shall, at his own costs and expenses, inspect the Equipment and issue the ex-work quality certificate.

9.3 The open-case inspection of the Equipment shall be performed by the Buyer in the presence of the Seller’s representatives on the Job Site in days after the arrival of the Equipment at the Job Site. The open-case inspection fee shall be borne by the Buyer.

The Buyer shall inform the Seller of the date one (1) month before the date of open case inspection and shall also render assistance to the Seller’s representatives in their inspection work.

9.4 During the joint open-case inspection, a detailed inspection record shall be made and signed by the representatives of both parties.

In case the Seller is responsible for any defect or shortage of the Equipment, the inspection record shall be taken as an effective evidence for the Buyer to claim repair, replacement or supplement to the Seller. Any of such claims shall be lodged by the Buyer within month(s) after the arrival of the Equipment at the Job Site.

9.5 If any shortage, defect of or damage to the Equipment is found in open-case inspection not attributable to the Seller’s responsibility, the Seller shall make repair, replacement or supplement at the Buyer’s expenses in accordance with the separate agreement signed by both parties.

9.6 The Buyer is not entitled to open the case, assemble and/or disassemble the Equipment without the Seller’s prior written consent.

If there is no joint open case inspection due to the reasons not attributable to the Seller, the quantity and apparent quality of the Equipment shall be deemed correct and in perfect condition.

Article 10 Design and Design Liaison

10.1 The Buyer shall provide to the Seller within ____ ( ) days after the Effective Date of the Contract, all the design data which shall be taken as the design basis. The Seller shall not be liable to the Buyer for, and the Buyer shall indemnify the Seller and hold the Seller harmless from any damages or failure caused by the incompleteness, incorrectness and/or inaccuracy of any such information and data.

10.2 A design liaison meeting shall be held in the ____ ( ) month after receiving above mentioned design data, the Seller will dispatch his technical personnel to the Job Site to participate in the meeting. During the meeting period, the Seller will discuss with the Buyer the relevant design details. Both parties shall sign an agreement outlining the design details.

10.3 During the design liaison meeting, the Seller and the Buyer shall provide assistance to the other’s dispatched personnel in arranging entry visas to the respective countries. The expense incurred on the dispatched personnel shall be borne by the party respectively.

Article 11 Erection, Test Run, Commissioning, Performance Test and Acceptance

11.1 The Erection, Test Run, Commissioning, Performance Test shall be conducted by the Buyer.

11.2 Chief Representatives

11.2.1 Each party shall nominate one (1) Chief Representative to deal with the technical matters during the period from the start of the Erection to Acceptance of the Equipment.

11.2.2 Detailed arrangements shall be made through friendly discussions by the Chief Representatives of both parties. The Chief Representatives of both parties shall fully cooperate to carry out their duties stipulated in the Contract, however they have no right to revise, alter or amend the Contract without the written authorization of both parties.

11.2.3 The Chief Representatives of both parties shall communicate through Linking Sheet for the matters relative to opinions, suggestions and information. The linking sheet shall be countersigned by the other party.

11.3 Erection and Test Run

11.3.1 The Erection shall be completed by the Buyer in ____ ( ) days from the effective date of the Contract. The Seller’s Chief Representative shall arrive at the Job Site ____ ( ) days prior to the beginning of the Erection.

11.3.2 When Erection is completed and in full conformity with requirements of the Technical Documentation, a Certificate of Completion for Erection of the Equipment shall be signed by the Chief Representatives of both parties in two (2) originals, one for each party, within three (3) days. The date of signing said Certificate shall be deemed as the date of completion of Erection.

11.3.3 As soon as the completion of Erection, Test Run for single machine and the whole system of the Equipment shall be started.

11.3.4 When Test Run has been successfully performed, a Certificate of Completion for Test Run of the Equipment shall be signed by the Chief Representatives of both parties in two (2) originals, one for each party, within three (3) days. The date of signing the said Certificates shall be deemed as the date of completion of Test Run of the Equipment.

11.4 Commissioning and Performance Test

11.4.1 Within ____ ( ) days after the completion of the Test Run, the Buyer shall make available qualified operation and maintenance personnel, raw materials, spare parts, utilities and other matters required for the Commissioning. Detailed procedures such as instrument calibrating, items of recording, sampling methods and analyzing methods, which are necessary for the Commissioning shall be discussed and agreed upon by the Chief Representatives of both parties.

If in the opinion of both parties, the Equipment is ready for the Commissioning, both parties shall confirm the readiness for the Commissioning in writing.

11.4.2 The Commissioning of the Equipment shall be started immediately after the confirmation of the readiness for the Commissioning. The Commissioning period shall ____ ( ) days after commencement of the Commissioning.

11.4.3 When the Seller and the Buyer consider that stable operation of the Equipment has been achieved, the date of Performance Test shall be fixed by Chief Representatives of both parties.

11.4.4 The Seller shall have the right to access to the laboratory and testing facilities in order to take samples and make analytical tests. The sample taking and analytical test during the Commissioning period will be done in the presence of the Chief Representatives of both parties.

11.4.5 During the period of Commissioning until Acceptance of the Equipment, the Seller may use the Buyer’s stored spare parts. Should the Buyer’s stored spare parts be used by the Seller due to the Seller’s responsibility, the Seller shall replenish the stores with the same in time at Job Site; otherwise the Seller shall provide the same at the Buyer’s costs upon the Buyer’s timely request.

11.4.6 If the result of Performance Test has reached the guarantee figures as per Appendix 1, the Acceptance Certificate of the Equipment shall be signed by the Chief Representatives of both parties in two (2) originals, one for each party, within three (3) days.

11.4.7 If the Performance Test cannot meet guarantee figures specified in Appendix 1, both parties shall jointly make investigations so as to find out the reason for clarifying the responsibility.

11.4.8 If the guarantee figures are not met due to the Seller’s reason, the Buyer shall agree to give an extension of ____ ( ) months so that the Seller can make improvement or adjustment to the Equipment and conduct further Performance Test. All the costs and expenses for making improvement or adjustment to the Equipment shall be borne by the Seller.

11.4.9 During the extension period, if the guarantee figures are still not met due to the Seller’s reason, the Seller shall pay the liquidated damages as per Appendix 1 to the Buyer against the Acceptance Certificate signed by both parties.

The Seller’s aggregate liability to pay liquidated damages for failure to attain the performance guarantees shall not exceed ____ ( ) percent of the Equipment price. The Seller shall have no further liability whatsoever to the Buyer in respect of such failure after payment of the liquidated damages.

11.4.10 If the non-achievement of the guarantee figures is due to the reasons not attributable to the Seller, the Seller shall agree to give an extension of ____ ( ) months. During the extension period all costs thereto incurred for the adjustment of the Equipment, as well as the costs and expenses for the Seller’s technical personnel shall be borne by the Buyer. In case the guarantee figures still can not be achieved due to the reasons not attributable to the Seller in the extension period, the Equipment shall be accepted by the Buyer. Both parties shall sign the Acceptance Certificate.

11.5 Acceptance

11.5.1 Acceptance shall occur in respect of the Equipment when :

(a) Performance Test has been successfully completed as per the Article 11.4.6.; or

(b) The Performance Test has not been completed due to the reasons not attributable to the Seller such as delayed civil construction, lack of and/or any other inconformity of raw materials, spare parts of the Buyer’s scope of supply under Appendix 2, and utilities with the requirements of the Contract in the ____ ( ) months from the date of Bill of Lading of the Last Shipment; or

(c) The Seller has paid the liquidated damages as per Article 11.4.9; or

(d) The guarantee figures still can not be reached due to reasons not attributable to the Seller’s reason in the extension period as specified in Article 11.4.10; or

(e) The Buyer takes the single machine and the whole system of the Equipment into use without the Seller’s approval.

11.5.2 At any time after any of the events set out in Article 11.5.1 has occurred, the Seller may give a notice to the Buyer requesting the issuance of the Acceptance Certificate.

11.5.3 The Buyer shall within seven (7) days after receipt of the Seller’s notice, issue such Acceptance Certificate.

11.5.4 If within seven (7) days after receipt of the Seller’s notice, the Buyer fails to issue the Acceptance Certificate or fails to inform the Seller in writing, with convincing evidence, of the reason why the Buyer has not issued the Acceptance Certificate, the Equipment shall be deemed having been accepted on the seventh day of the Seller’s said notice.

11.5.5 After the Acceptance, the Seller’s responsibilities and obligations under the Contract shall be deemed having been fulfilled except those as stipulated in Article 12 and 14.

Article 12 Guarantee and Warranty

12.1 The Seller guarantees that:

(a) The Equipment supplied by the Seller shall be new and made of adequate materials, and in conformity with the technical requirements of the Contract;

(b) The Technical Documentation shall be complete, clear and correct.

12.2 The period of warranty given by the Seller under Article 12.1 shall be ____ ( ) months from the date of Acceptance or ____ ( ) months from the date of Last Shipment, whichever comes earlier.

12.3 Defect of the Equipment

12.3.1 During the Warranty Period, should any defect due to inferior materials or bad workmanship of the Equipment be found under normal operation, the Buyer shall give the Seller a notice stating the details, together with all available evidence.

The Seller shall take immediate action to eliminate the defect at the Seller’s expenses within the period agreed by both parties.

12.3.2 If certain defect can not be eliminated despite of several attempts, the Seller shall replace the defective parts with non-defective parts at the Seller’s costs and expenses.

12.3.3 If the defect is eliminated by the Buyer himself, subject to the Seller’s prior written consent, all the direct costs and expenses thus incurred shall be borne by the Seller.

12.3.4 The Seller may reduce the price of the defective Equipment according to the degree of inferiority or extent of damage as agreed by both parties. After the reduction the Seller shall be released from its obligations and liabilities.

12.3.5 During the Warranty Period, should any defect due to the Buyer’s improper operation or maintenance be found, the Seller will provide technical assistance to eliminate the defect or replace the defected parts upon Buyer’s requests. All the costs and expenses thus occurred shall be borne by the Buyer.

12.3.6 Subject to Article 12.3.1, The Seller shall not be responsible for any defect or damage to the Equipment arising out of any circumstances including but not limited to the following causes:

(a) Combination of the Equipment with any machinery, and/or component other than those supplied by the Seller; or

(b) Alteration, modification or repair without the Seller’s prior written consent; or

(c) Failure of the Buyer to follow the Technical Documentation and instructions of the Seller, including the Buyer’s improper operation and maintenance; or

(d) Normal wear and tear.

12.4 During the Warranty Period, should the Technical Documentation supplied by the Seller be found incomplete, unclear or incorrect due to the Seller’s reason, the Seller shall be liable to supplement, replace or correct the Technical Documentation free of charge.

12.5 The Seller shall in no respect be understood or interpreted as liable for the commercial development of the Contract Products. The Buyer shall undertake the risk of the commercial development of the Contract Products.

12.6 In no circumstances, whether as a result of breach of contract, warranty, indemnity, tort (including negligence), strict liability, or otherwise, shall the Seller or its subcontractors or suppliers be liable for loss of profit or revenues, loss of production, loss of use, loss of information or data, cost of capital, cost of substitute equipment, facilities, services or replacement power, downtime costs, claims of the Buyer’s customers for such damages, or for any special, consequential, incidental, indirect or exemplary damages.

12.7 Notwithstanding anything to the contrary provided in the Contract, the aggregate liability of the Seller to the Buyer , on all claims of any kind, whether in contract, warranty, indemnity, tort (including negligence), strict liability, or otherwise, arising out of the performance or breach of the Contract or use of any Equipment or exploration of the Patent and/or Know-how shall not exceed ____ ( ) percent of the total Contract price.

12.8 All Contractual obligations of the Seller shall be deemed as having been fulfilled upon the expiry date of the Warranty Period.

Article 13 Intellectual Property Right

13.1 The Seller represents that it is entitled or authorized to grant the license to the Buyer to use the Patent and/or Know-how for the purpose as specified in Article 3.

13.2 The Buyer shall not use such Patent and/or know-how received from the Seller for any purpose other than that as specified in this Contract.

13.3 Any intellectual property right or other technical information granted by the Seller to the Buyer shall remain the property of the Seller. In no circumstances shall any terms and conditions in this Contract be construed, deemed, or interpreted as transfer of title to the Buyer of any information which may be delivered to or accessed by the Buyer.

13.4 Registration of the Contract and Maintenance of Patent

13.4.1 The Buyer shall, after the Contract is signed between both parties, make sure that the Contract is registered with or filed to the competent authorities in the Buyer’s country if it is required by law.

13.4.2 The Seller shall, during the validity period of the Contract, make all reasonable efforts to maintain Patent in force in the territory as stipulated in Article 3.4.1 and bear the costs thus incurred. The Buyer shall not make any action or inaction which may lead to invalidation or compulsory licensing of the Patent.

13.5 Improvement and Grant-back

13.5.1 Should any Improvement be made by the Seller on Patent and/or Know-how within the validity period of the Contract, which shall be the exclusive property of the Seller, the Seller shall grant the Buyer a non-exclusive license to exploit such Improvement at latest __________months from its improving, provided that the license fee is agreed upon between both parties.

13.5.2 The Buyer shall be entitled to make Improvement on Patent and/or Know-how within the validity period of the Contract. The Seller shall have the right to obtain and make use of the Improvement. The license fee shall be discussed between both parties in due time.

13.5.3 Both parties shall keep Improvement confidential. Neither party shall be entitled to grant any third party a sub-license on Improvement made and provided by the other party without previous written consent of the other party.

Article 14 Confidentiality

14.1 After signing of the Contract, both parties shall keep secret all the contents, terms, conditions of the Contract.

14.2 The Buyer shall take proper measures to keep strictly confidential of Know-how, Technical Documentation, Improvement and any other secret information obtained or accessible to from the Seller. The Buyer shall not disclose any of them to any third party, and shall not make use of them without prior written consent of the Seller except otherwise stipulated in the Contract.

14.3 The Buyer may disclose the secret information as described in Article 14.2 to the personnel of its own, or of any related parties engaged in the performance of the Contract subject to Article 14.2, strictly to the extent as essential for the implementation of the Contract, provided that the individuals and/or parties accessing or may access such secret information are engaged to undertake in written form the same confidential liability of the Buyer to the Seller. Any breach of confidentiality obligations by any personnel from the Buyer or the Buyer’s related parties shall be deemed as breach of the Contract by the Buyer.

14.4 Notwithstanding this Article 14, the Seller may furnish to its sub-contractor such documents, data, and other information received from the Buyer to the extent required for performing the Contract, in which event the Seller shall obtain from such sub-contractor an undertaking of confidentiality similar to that imposed on the Seller under the Article 14.

14.5 This Article 14 shall survive the expiration or termination of the Contract.

14.6 The confidential obligation shall not apply to the information which:

A. now or hereafter enters the public domain; or

B. can be proved to have been in the possession of the Party at the time of disclosure and which was not previously obtained, directly or indirectly, from the other Party hereto; or

C. otherwise lawfully becomes available to either party from a third party under no obligation of confidentiality.

Article 15 Taxes and Duties

15.1 All taxes and duties in connection with the signing and performance of the Contract, levied by Governments of the People’s Republic of China, including but not limited to customs duties, income tax, sales tax, value-added tax etc., shall be borne and paid by the Seller.

15.2. All taxes and duties in connection with the signing and performance of the Contract levied on the Buyer and Seller by the Buyer’s Governments, including but not limited to customs duties, income tax, sales tax, value-added tax etc., shall be borne and paid by the Buyer. The Buyer shall pay in due time and full amount and hold the Seller harmless from any taxes and duties in case incurred to the Seller in the signing and performance of the Contract.

15.3 All import taxes and duties for tools and/or instruments, which the Seller or the Seller’s personnel may bring to the Buyer’s country for the execution of the Contract, shall be borne and paid by the Buyer.

15.4 Any and all taxes and duties in connection with the signing and performance of the Contract levied in any place except the cases as specified in Article 15.1 are not included in the Contract price. Should the Seller make the relevant payment directly as the case may be, both Parties agree to amend the Contract price to fully compensate the Seller for the payment, and the Buyer shall fully refund the Seller for the relevant amount within_______( ) days from the Seller’s payment.

Article 16 Force Majeure

16.1 If either of the Contract parties is prevented from executing the Contract due to the event of Force Majeure such as war, riot, coup, embargo, flood, typhoon, tornado, snowstorm, earthquake and other events which could not be foreseen, avoided and overcome, the affected party shall notify the other party by fax within the shortest possible time of occurrences of the Force Majeure and send a certificate issued by competent authorities or agency certifying the event of the Force Majeure by registered or express mail within fourteen (14) days following its occurrence.

16.2 The affected party shall not be liable for any delay or failure in performing any of its obligations due to the event of Force Majeure. However the affected party shall inform the other party by fax the termination or elimination of the event of Force Majeure as soon as possible.

16.3 Both parties shall proceed with their obligations immediately upon the cease of the event of Force Majeure or the removal of the effects and the term of the Contract shall be extended correspondingly. Should the effect of the event of Force Majeure last for more than one hundred and twenty (120) days, either party shall have the right to terminate the Contract by a written notice.

Article 17 Applicable Law and Settlement of Disputes

17.1 The applicable law of the Contract shall be the laws of the People’s Republic of China.

17.2 All disputes arising from or in connection with the Contract shall be settled through friendly consultation between both parties. In case no agreement can be reached, the dispute shall be submitted for arbitration.

17.3 The arbitration shall be conducted by China International Economic and Trade Arbitration Commission (CIETAC) in Beijing in accordance with Arbitration Rules of the Commission in effect at the time of applying for arbitration. The tribunal shall be composed of three arbitrators.

17.4 The arbitral award shall be final and binding upon both parties.

17.5 During proceedings of arbitration, the undisputed part of the Contract shall be performed continuously by both parties regardless of such arbitration proceedings.

Article 18 Effectiveness, Term and Termination of the Contract

(a) The Seller and the Buyer sign the Contract;

(b) The Contract shall be approved by the competent authorities and/or banks of both parties (if applicable);

(c) The Seller receives the Down Payment;

(d) The Seller duly receives the L/C (or L/G ) issued by the Buyers Bank.

18.2 Each party shall use its best efforts to fulfill the above conditions for which it is responsible as soon as practicable.

18.3 If the Contract has not become effective pursuant to Article 18.1 within ____ ( ) months after the date of signing this Contract, the Seller has the right to make an equitable adjustment to the total Contract price and the time for delivery and/or other relevant conditions of the Contract. Should no agreement is reached for the above mentioned adjustment within ____ ( ) days from the Seller’s request of adjustment, the Seller shall be entitled to cancel the Contract.

18.4 The Contract shall be valid and remain in force for_____ (_____) years from the Date of Effectiveness, during which period the Buyer shall be entitled to manufacture the Contract Products with Patent and/or Know-how and sell the Contract Products within the licensed territory as specified in Article 3.4.

(Option 1) The Buyer shall not be entitled to manufacture with patent and/or know-how or sell the contract products after the aforesaid period unless the Buyer agrees to pay additional license fees in the amount and with the payment schedules and methods as agreed upon between both Parties in due time.

(Option 2) The Buyer shall be entitled to manufacture with Patent and/or Know-how or sell the Contract Products after expiration of the Contract term specified above, provided that the Buyer shall not be released from its confidential obligations under the Contract.

(Option 3) The Buyer shall not be entitled to manufacture with Patent and/or Know-how or sell the Contract Products after the expiration of the Contract term specified above, and shall return to the Seller all the Technical Documentations specified in Appendix 4 without remaining any duplicate copies. Nevertheless the confidential obligations of the Buyer under Article 14 shall survive the Contract term.

18.5 Either party may, without prejudice to any other remedy for the other party’s following breach of the Contract, terminate the Contract in whole or in part by a written notice send to the other party, if the other party

A. fails to perform its payment obligation under the Contract and does not remedy for its failure within a period of ______ (____) days upon receipt of the written notice or a period agreed upon between the parties; or

B. fails to perform its confidentiality obligation under the Contract; or

C. fails to perform any other obligations under the Contract except minor parts thereof, and does not remedy for its failure within a period of ______ (____) days upon receipt of the written notice or a period agreed upon between the parties; or

D. becomes bankrupt or insolvent, goes into liquidation, has a receiving or administration order made against him, compounds with his creditors, or carries on business under a receiver, trustee or manager for the benefit of his creditors, or dissolves, or ceases to do business, or be ordered to close down / to cease to do business / to dissolve, or has its business license revoked, or if any act is done or event occurs which (under applicable Laws) has a similar effect to any of these acts or events.

18.6 Either party may, without prejudice to any other remedy, terminate the Contract in whole or in part by a written notice send to the other party, if

A. The other party is prevented by the laws, statutes, rules or regulations of either country from performing its obligations under the Contract; or

B. The Seller is prevented by the relevant authority of the Buyer’s country from being paid in accordance with the Contract; or

C. The other party is prevented from performing its contractual obligations by any event of Force Majeure for more than one hundred and twenty (120) days.

18.7 In the event of termination of the Contract, without prejudice to any other remedies available according to the Contract and/or applicable laws,

The Buyer shall cease all its further exploitation of the Patent and/or Know-how and any acceptance of further orders from third parties for the Contract Products.

All the delivered literatures, drawings, samples, instruments, equipment, and other documents including the interpretations related to Patent and/or Know-how shall be returned to the Seller as the Seller’s requests.

All the contracts on sales of the Contract Products signed between the Buyer and third parties shall be terminated by the Buyer, otherwise the Seller shall be paid accordingly.

In case the termination is due to the Seller’s default, the Buyer shall be entitled to complete the performance of the contracts on sales of the Contract Products already signed between the Buyer and third parties before the termination.

The Seller shall be paid by the Buyer for all the contractual obligations performed by the Seller till the date of termination within _______days from receipt of the termination notice.

E. Termination of the Contract shall not release either party from its confidential obligations under the Contract

Article 19 Miscellaneous

19.1 The Contract is signed by the authorized representatives of both parties in ____ ( ) originals. Each party shall keep ____ ( ).

19.2 The Contract supersedes all communications, negotiations and agreements between the parties prior to the signing date of this Contract.

19.3 All amendments, supplements and alternations to terms of the Contract shall be made in written form and signed by the authorized representatives of both parties. These amendments, supplements and alternations shall form integral parts of the Contract.

If any costs occur or delivery delay due to amendment or explanation of the new law or statute or regulations enacted by the Buyer’s country after the effectiveness of the Contract，the Seller shall have the right to ask for necessary adjustment in relation to the Contract price and the delivery schedule.

19.4 No assignment, cession, novation, or transfer of any right or obligation under this Contract shall be made by either party to a third party without the prior written consent of the other party.

19.5 All communications between both parties in the course of implementation of the Contract should be in English language in written form at the address set forth below. The faxes concerning the important matters shall be confirmed in due time by registered or express mail or letter delivered by hand.

The Buyer:

Address:

Post Code:

Fax: __________________________

Tel.: __________________________

Email:__________________________

Attention: ______________________

The Seller :

Address:

Post Code:

Fax: __________________________

Tel.: __________________________

Email:__________________________

Attention: ______________________

IN WITNESS WHEREOF, the parties hereto have caused this Contract to be duly executed.

The Buyer:

The Seller:

By:______________________[Signature]

Name: [printed name]

By:_______________________ [Signature]

Name: [printed name]

Title:

Title:

Appendices

Appendix 1 Specifications and Guarantee Indices (Omitted)

暑假仓储管理实习报告范文

一、实习目的

安排学生到仓储类物流企业实习基地实习,在企业实训教师的指导下,熟悉仓储类企业的物流作业流程,了解仓库物品管理及基规定,了解仓储结算等手续,最后写出专题实习报告

二、实习时间

12年暑假

三、实习地点

吴中物流有限责任公司

四、指导老师

鲁雅亲老师

五、实习内容

“仓”也称为仓库，为存放物品的建筑物和场地，可以为房屋建筑、大型容器、洞穴或者特定的场地等，具有存放和保护物品的功能；“储”表示收存以备使用，具有收存、保管、交付使用的意思，当适用有形物品时也称为储存。“仓储”则为利用仓库存放、储存未即时使用的物品的行为。简言之，仓储就是在特定的场所储存物品的行为。

通过暑假两个月在物流公司的实习同时结合书本上的知识使我对仓储有了更深的认识，现从以下几个部分讲：

第一部分：自我介绍

我是公司储运部吴中仓库的仓库保管员：我是今年七月一号进入公司工作的，作为一名新员工进入了一家高速发展的物流公司工作，深感欣喜。我想这是我职业的新开始。

第二部分：人力的合理安排和运用

1：人力的安排

作为物流公司的传统业务———仓储，虽然技术性并不高，但需要勤劳，心细，作业强度大，体力要求比较高。象我们吴中仓库，随着客户的不断进入，业务不断增多，原本在人力方面就比较紧凑，这就要我们合理安排装卸工人，做到在有限的人力上作合理的安排，做到有条不紊，作业顺，这时就要合理安排人员，使每一作业尽量不受影响。

2：合理的休息

在出口装箱时，高温季节，仓储作业量大，出汗多。像卫洗丽的箱子，每一箱成品都套有一个塑料袋，很滑，装箱时不能碰伤箱子，作业要求高，难度大。在40多度的箱内，一会儿就汗流浃背了，所以要合理安排作业和休息，做到轮流休息，不间断作业，这样在保证作业安全的情况下，作业效率就不受影响了。

3：人员的培训和提高

虽然装卸工人的工作比较简单，但为了作业的不断提高，我们也要不断提醒他们现场作业的规定，及客户对我们的要求，这样有利于我们对仓库的管理，理货，配货等作业。他们的作业效率也会有所提高的。

第三部分：货物的管理

吴中仓库开业六个多月来，味之素，toto上海工厂，toto卫洗丽的业务已相继进入吴中仓库。客户的成品，出口品部分或全部进入吴中仓库进行保管。所以要做好仓库的管理，货物的入出库作业，日常保管，仓库清理工作，把好库存数量的管理，防止不必要的损耗的发生，有效的利用库存区面积。

a：易拿，易放，易看，易点的堆积方式，

b：货物堆放不要超过托盘，不要超高堆放，要注意“五距”，

c：货物入出时做好桩脚卡记录（计好箱数和枚数）

d：坚持货物先进先出，对于频繁进出库的货物和小件的货物应多盘点这样减少库存差异

e：保持仓库的整洁，地面的清洁，通道的顺畅

主要有：

一、部品的管理

1 ：部品的入库作业

现toto上海工厂的大部分部品已进入松江仓库保管，部品作为成品的一个部件，其种类繁多，大致分f部品和d部品，从加工手册上有分手册品（保税品———存放在保税区域）和非手册品，保管也有不同的要求。部品在转库进入仓库时，往往比较乱：部品外箱比较破因为它是周转箱，要用到不能用为止的。而且进来的端数有时乱，要整理清点每一个型号，箱数，端数；特别注意的是d部品中的便坐器系列的部品，它是toto工厂中直接生产线出来由仓库开转库单过开的，不像他们协力厂过来的部品那样整齐，所以一定要多留神，多注意清点。

共2页，当前第1页12

与时俱进的物业管理

与时俱进的物业管理

作者： 来源：

——在美佳物业伟柏花园管理处的实习报告

今年一月十八日下午开始，我在美佳物业伟柏花园进行了物业管理实习工作。在实习期间，我依次对设施管理、事务管理、保安管理进行了实习。在实习中，我在管理处指导老师的热心指导下，积极参与物业管理相关工作，注意把书本上学到的物业管理理论知识对照实际工作，用理论知识加深对实际工作的认识，用实践验证所学的物业管理理论，探求物业管理工作的本质与规律。简短的实习生活，既紧张，又新奇，收获也很多。通过实习，使我对物业管理工作有了深层次的感性与理性的认识。

我所实习的美佳物业管理有限公司，隶属于香港沿海绿色家园集团。目前，该公司拥有员工近1500人，在深圳、厦门、福州、上海、武汉、鞍山、北京、大连、长沙等大中城市均有物业管理的项目。管理面积约300万平方米，管理项目类别有大型住宅区、高层商住大厦、商场、公寓、别墅、酒店、高等院校等物业。伟柏花园是其所管辖的物业管理项目之一。伟柏花园由2栋19层高的塔楼组合而成，小区面积约29000平方米，居住270户，居住人口近一千人，管理处员工26人，其中：管理人员6人。

回顾实习生活，感触是很深的，收获是丰硕的。实习中，我采用了看、问等方式，对伟柏花园管理处的物业管理工作的开展有了进一步的了解，分析了管理处开展物业管理有关工作的特点、方式、运作规律。同时，对管理处的设施管理、事务管理、保安管理有了初步了解。

一、加强人力资源管理，创“学习型、创新型”企业。

严把员工招聘关。美佳物业在招聘管理人员须毕业于物业管理专业；招聘维修人员须具备相关技术条件的多面手，并持有《上岗证》；招聘安保人员须属退伍军人，对其身高、体能、知识、品格、心理素质等都进行严格考核挑选。

做好员工的入职、在职培训工作。美佳物业对新招聘的员工进行上岗前的相关培训工作，使员工对小区的基本情况、应开展的工作心中有数，减少盲目性；随着市场竞争激烈，知识、技能的不断更新，对在职员工提供各类专业性的培训机会。美佳物业提倡“工作就是学习，工作就是创新”，每位员工都争做“学习型、创新型”员工，员工中形成了一种积极向上的比帮赶超的竞争氛围。从而，使员工个人素质得以提高，管理处的管理服务水平和管理效益得以提高，树立了良好的企业形象。

从实际出发，管理处严格参照lS09000质量体系运作，制定了严格的规章制度和岗位规程、工作标准、考核标准。管理处根据员工的工作职责，制定全方位的上级、平级、下级的360度考核办法；制定量化考核标准，实行定性和定量考核相结合，增强了考核的可操作性，减少考核时人为因素的影响；建立完善考核机制，实行末位淘汰制，避免了考核走过场的现象，通过考核机制的建立，增强了员工的危机感、紧迫感，促使员工不断提高自身素质。

二、培育自身核心专长，创特色服务，提升核心竞争力。

在实习中，我看到一套由沿海集团、易建科技、美佳物业合作自行设计开发的“一站式物业管理资迅系统”物业管理服务软件。该软件包括：“一站式客户服务、一站式资迅管理、一站式数码社区”三大体系，是一个利用网络、电子商务、科技手段来提高物业管理水平和服务质量，有效地开发、整合、利用客户资源的资迅系统。管理处全面提倡“一站式服务”、“最佳保安”的特色管理服务。从而，实现了高效的管理运作，解决了业主的奔波之苦，创造了一种无微不至、无所不在的服务，提升了服务效率，提高了业主满意度，提升了物业管理服务的水平和服务质量，最终提升了公司在激烈的市场竞争中的核心竞争力。

三、推行“顾客互动年”，促进公司与业主之间的良性互动。

美佳物业在与业主关系管理方面，在实习中我了解到，在XX年美佳重点开展了“顾客互动年”活动。成立了美佳俱乐部，设立新生活服务中心，开通客户服务热线，及根据小区居住的业主不同的年龄、不同的爱好与兴趣、不同的层次等，有针对性地开展日常的社区活动与主题活动。如：三月份，开展了学雷锋义务服务活动；“六一”儿童节，与幼儿园联谊开展游戏活动；十月份，组织小区业主观看露天电影；十二月份，圣诞节由圣诞老人派发圣诞礼物……通过开展各类丰富多彩的互动活动，加强了公司与业主、业主与业主之间的沟通交流，创建了互动的顾客关系，营造了浓厚的社区氛围和良好的居住环境。

四、重视物业管理的重要基础工作——设备管理。

对于设备管理，我在实习中看到，管理处着重建立和完善设备管理制度；对各类设备都建立设备卡片；做好设备的日常检查巡视，定期进行检查、保养、维修、清洁，并认真作好记录，发现问题及时解决。如对水池、水箱半年清洗消毒一次，进行水质化验，以保证水质符合国家标准；发电机每月试运行一次；消防泵每月点动一次，以确保发生火灾险情时，消防泵能正常使用。等等。

五、管理处一道亮丽的风景线——安保队伍。

共2页，当前第1页12

甲方：餐饮管理有限公司

乙方：

甲方因企业发展和规范管理、科学管理的需要，而乙方在上述方面具有相应知识和工作经验，双方本着平等、自愿和互惠原则，通过充分协商，就甲方聘用乙方为其企业高级管理职位，全权负责公司管理经营，达成如下协议：

一、聘用期限

1.1聘用期为     年，即自       年      月     日至        年     月     日。

1.2 乙方保证在甲方报到上班时与其它企业无劳动聘用关系。

1.3双方约定试用期为   个月，即       年      月     日至        年     月     日。试用期内甲乙双方根据情况均可提出解除合同。

二、双方工作职责及义务

2.1  甲方聘用乙方为  店长  ，具体岗位职责由甲方在征询乙方意愿的前提下根据甲方情况确定，包括但不限于             。

2.2乙方工作职责由岗位责任制度和相关制度进行规范。乙方须充分运用其专业知识与工作经验，保持严谨的工作风格和勤勉的工作态度，恰当且如实履行其工作职责。

2.3乙方须遵守甲方的各项管理制度和尊重甲方企业文化，服从甲方的工作安排。

2.4乙方不得在受聘期间从事以谋取个人利益为目的经营活动；不得在别的企业或单位兼职。

2.5 乙方离开职后，不得从事直接有损甲方利益的职业或活动。

三、乙方福利及薪资待遇

3.1以下两部分构成乙方任职期间的待遇，二者不关联。

3.1.1为了增加乙方在经营期间的积极性，自本合同签订之日起，根据每个会计年度进行核算，若公司盈利乙方可获得甲方公司20%的利润分红。

3.1.2乙方的薪资待遇按照如下方案施行：第一个月按照考核制度，第一月公司为6000元；第二个月按照业绩考核，毛利率考核，会员充值考核，例如第二月业绩为35万，会员充值10万，毛利率达成56%--62%，即可拿到全额工资及奖金，6500元，如完成各项考核的70%，工资5500元，完成各项考核的50%，工资4000元，完成各项考核的50％以下，仅获得基本工资2800元；第三月业绩及毛利率，会员卡比例比第二月提升30%作为考核点，乙方工资为7000元，作为目标公司第四月为稳定发展上升阶段，作为目标公司聘请职业经理人，严格控制店里成本及提成目标利润空间，详细内容可以参考附件（合肥餐饮管理有限公司店长薪资制度）。

3.2若公司盈利，乙方可于每年     获得利润分红。乙方薪资发放方式：按月发放乙方的月工资为每月   日；

3.4乙方在任期期间主动提出离职的，

四、工作时间、休息及休假方面

乙方作为企业高级管理人员，工作时间应当积极遵守企业规章制度的规定，严格自律。因餐饮行业的特殊性，导致乙方双休日或者节假日加班的，乙方可以自性安排时间调休，甲方不对乙方出勤进行考核也不认可甲方任何加班费请求。

五、“商业及技术秘密”保密条款

5.1甲方“商业和技术秘密”包括甲方和生产、技术、销售/财务、行政人事、对外投资等经营管理活动相关的各种信息。

5.2自本合同签订之日起乙方严格遵守甲方制定的关于“商业及技术秘密”（及载体）的有管理制度和本合同约定的保密条款，不得以任何理由、任何方式（法律规定应披露的情形以外）向他方及公司员工披露或加以利用。

5.3当甲乙双方终止本合同后，乙方须承诺遵守“商业及技术秘密”保密条款。

六、“同业竞争限制”条款

甲乙双方解除合同关系后两年内，乙方必须遵守以下同业竞争限制行为，否则，甲方保留通过法律途径追究乙方责任的权利：

①乙方不得在甲方认定产生同业竞争的企业或单位任职、兼职或服务；

②乙方不得投资组建甲方认定产生同业竞争的企业和单位；

③乙方不得教唆或其它方式说服甲方员工加入同行竞争的企业和单位；

④乙方不得直接和间接对甲方客户销售或提供与甲方相同或类似的产品与服务；

⑤甲方认定产生同业竞争的其它行为。

七、本合同的变更、解除、终止

7.1经甲乙一致同意，合同可以变更、解除，一方造成损失的应当赔偿另一方损失。

7.2乙方应当保证所提供的个人信息真实有效，否则甲方可以立即解除本合同。

7.3乙方在未经甲方同意的情况下离职除承担违约责任以外乙方还应承担由此对甲方造成的一切经济损失。

八、违约责任以及合同纠纷处理

8.1本合同履行期间发生争议的，双方可协商纠纷，达不成协议的，可向法院提起诉讼。

8.2违约责任及违约金：如甲乙双方任何一方违约方应承担的违约金为人民币     万元，除承担违约金外还应承担由此对另一方造成的一切经济损失。

九、其他事项

9.1本合同经甲乙双方盖章或签字后生效

9.2本合同未尽事宜甲乙双方可签订补充协议。

9.3本合同一式二份，甲乙双方各执一份

甲方（盖章）：               乙方（签字）：

法人代表（签字）：           乙方代表（签字）：

合同签订日期：    年   月    日

1.负责互联网软件产品、游戏研发的日常项目管理工作，参与产品研发的整个生命周期，包括项目预研、项目启动、项目计划、项目执行和控制等各个阶段。

2.负责项目风险控制，及时发现并解决影响项目进度的相关问题。

3. 负责项目计划和时间表的制定或审核，组织项目各项评审会，跟踪项目开展，确保项目按期实现。

4.负责项目资源协调与组织，建立清晰高效的沟通机制，推进团队内外部沟通协调，确保项目团队协同工作。

5.协助部门主管进行部门事务管理。

职责：

1、 负责项目立项、任务下达;

2、 负责合同拟定，打印寄送，合同归档管理;

3、 跟进项目进展，沟通协调推动相关干系人按计划完成工作;

4、 项目资料收集、汇总归档;

5、 协助项目经理及市场人员项目款结算;

6、 及时完成领导交代的其他任务。

任职要求：

1、工作积极主动，具有高度的责任感和保密意识;

2、具备良好的计划组织，沟通协调能力，执行能力强，有较强的工作推动力及承担压力的能力;

3、善于发现并解决问题，逻辑思维能力强;

4、大专及以上学历，测绘、gis、工程管理等相关专业， 有项目管理相关工作经验优先。

技术转让（专利申请权）合同

合同编号：

技术转让(专利申请权)合同

(示范文本)

项目名称：

受 让 方：

(甲 方)

让 与 方：

(乙 方)

签订时间：

签订地点：

中华人民共和国科学技术部印制

项目名称：

受让方(甲 方)：

让与方(乙 方)：

签订时间：

签订地点：

有效期限：

中华人民共和国科学技术部印制

填 写 说 明

一、

本合同为中华人民共和国科学技术部印制的技术转让(专利申请权)合同示范文本，各技术合同登记机构可推介技术合同当事人参照使用。

二、

本合同书适用于一方当事人一方(让与方)将其就特定的发明创造申请专利的权利转让受让方，受让方支付约定价款而订立的合同。

三、

签约一方为多个当事人的，可按各自在合同关系中的作用等，在“委托方”、“受托方”项下(增页)分别排列为共同受让人或共同让与人。

四、

本合同书未尽事项，可由当事人附页另行约定，并作为本合同的组成部分。

五、

当事人使用本合同书时约定无需填写的条款，应在该条款处注明“无技术转让(专利申请权)合同

项目名称：

受让方(甲方)：

法定代表人：

住 所 地：

法定代表人：

项目联系人：

联系方式

通讯地址：

电

话：

传

真：

电子信箱：

住 所 地：

让与方(乙方)：

住 所 地：

法定代表人：

项目联系人：

联系方式

通讯地址：

电

话：

传

真：

电子信箱：

法定代表人：

住 所 地：

本合同乙方拥有的技术发明创造，甲方受让该项技术发明的专利申请权并支付相应的转让价款。本合同受让方与让与方(以下称“双方”)就约定发明创造的就此项专利申请权转让事项，经过平等协商，在真实、充分地表达各自意愿的基础上，根据《中华人民共和国民法典》的规定，达成如下协议，并由双方共同恪守。

第一条 鉴于乙方拥有

的技术发明，甲方希望得到该项技术发明的专利申请权并支付相应的转让价款。

第二条：本项发明创造的专利申请权：

1.属于

(发明、实用新型、外观设计)申请。

2.发明人/设计人：为

。

3.专利申请人：

。

4.专利申请日：

。

5.专利申请号：

。

第三条 乙方在本合同签署生效前实施使用或转让本项发明创造的状况如下：

1. 乙方实施自行使用本发明创造的状况(时间、地点、方式和规模)：

2. 乙方许可他人使用本发明创造的状况(时间、地点、方式和规模)：

3.本合同生效后，乙方有义务在

日内将本发明创造专利申请权转让的状况告知被许可使用本发明创造的当事人。

第四条 甲方应在本合同生效后，保证原技术转让合同的履行。

乙方在原技术转让合同中享有的权利和义务，自本合同生效之日起，由甲方承受。乙方应当在

日内通知并协助原技术转让合同的让与人与甲方办理变更原专利实施许可合同变更事项。

第五条 为保证甲方申请专利，乙方应向甲方提交以下技术资料：

1.技术资料内容：

2.

3.

4.

第六条 乙方向甲方提交技术资料的时间、地点、方式如下;

1.提交时间：

2.提交地点：

3.提交方式：

第七条 乙方应当保证其专利申请权的合法性和真实性不侵犯任何第三人的合法权益。如发生第三人方指控甲方侵权的，应由乙方应当协助解决纠纷;如经最终法律程序确认甲方构成侵权，甲方有权要求乙方应当承担相应的赔偿责任。

第八条 甲方向乙方支付该发明创造专利申请权的价款及支付方式如下为：

1.专利申请权的转让价款总额为：

;

2.专利申请权的转让价款由甲方 (一次、分期或提成)支付乙方。

具体支付方式和时间如下：

(1)

(2)

(3)

乙方开户银行名称、地址和帐号为：

开户银行：

地址：

帐号：

3.双方确定，甲方以实施研究开发成果所产生的利益提成支付乙方的研究开发经费和报酬的，乙方有权以以适当的时间和方式查阅甲方有关的会计帐目。具体查阅办法为：

第九条 双方确定，本合同生效后，甲方专利申请被国务院专利行政部门驳回的，乙方不退还已收取的转让费用;尚未收取的，

按以下方式处理：

双方对专利申请被驳回的特别约定如下：

第十条 双方确定：

1.本合同生效后，甲方申请专利并取得专利权的，乙方应按以下约定乙方要求继续实施或使用该发明创造，应征得甲方的许可，另行订立专利实施许可合同 。

2.本合同生效后，该项甲方申请专利申请在专利公开前被驳回的，双方按以下约定实施或使用该发明创造：

第十一条 双方确定因履行本合同应遵守的保密义务如下：

1.甲方：

1.保密内容(包括技术信息和经营信息):

2.涉密人员范围:

3.保密期限：

4.泄密责任：

乙方：

1.保密内容(包括技术信息和经营信息):

2.涉密人员范围:

3.保密期限：

4.泄密责任：

第十一条 本合同签署后，由

方负责在

日内办理专利申请权转让的登记事宜。(1)保密范围:

A.人员:

B.技术资料和信息:

C.技术成果:

第十二条 双方确定：

1. 甲方有权利用乙方交付专利申请权所涉及的发明创造进行后续改进，由此产生的具有实质性或创造性技术进步特征的新的技术成果，归

(甲方、双方)方所有。具体相关利益的分配办法如下：

(2)保密期限：

(3)泄密责任：

2.乙方：

(1)保密范围:

A.人员:

B.技术资料和信息:

C.技术成果:

(2)保密期限：

(3)泄密责任：

第十一条：本合同生效后，由

方负责在

日内办理专利申请权转让合同的登记和公告事宜。

第十二条：双方确定：

1.甲方有权利用乙方交付的发明创造，在专利申请前及申请后进行后续改进。由此产生的具有实质性或创造性技术进步特征的新的技术成果，归

(甲方、双方)方所有。具体相关利益的分配办法如下：

2. 乙方有权在已交付甲方专利申请权后对此的发明创造后，在甲方专利申请前及申请后进行后续改进，由此产生的具有实质性或创造性技术进步特征的新的技术成果，归

(乙方、双方)方所有。具体相关利益的分配办法如下：

第十三条 双方确定

1.甲方违反本合同第

条、第

条、第

条、第

条，按以下第

种方式承担违约责任：

(1)支付

元违约金;

(2)按专利申请权转让价款的 %支付违约金;

(3)按乙方的实际损失支付赔偿金。乙方实际损失的范围和计算方法为：

2.乙方违反本合同第

条、第

条、第

条、第

条，按以下第

种方式承担违约责任：

(1)支付

元违约金;

(2)按专利申请权转让价款的 %支付违约金;

(3)按甲方的实际损失支付赔偿金。甲方实际损失的范围和计算方法为：

第十四条：双方确定，本合同应下列原因而终止：

1.双方确定的权利与义务履行完毕;按以下约定承担各自的违约责任：

1.

方违反本合同第

条约定，应当

(支付违约金或损失赔偿额的计算方法)。

2.

方违反本合同第

条约定，应当

(支付违约金或损失赔偿额的计算方法)。

3.

方违反本合同第

条约定，应当

(支付违约金或损失赔偿额的计算方法)。

4.

方违反本合同第

条约定，应当(支付违约金或损失赔偿额的计算方法)。

第十四条 双方确定，在本合同有效期内，甲方指定

为甲方项目联系人，乙方指定 为乙方项目联系人。项目联系人承担以下责任：

1.

;

2.

;

3.

。

一方变更项目联系人的，应当及时以书面形式通知另一方。未及时通知并影响本合同履行或造成损失的，应承担相应的责任。

第十五条 双方确定，出现下列情形，致使本合同的履行成为不必要或不可能的，可以解除本合同：

1.因发生不可抗力;

2.

;

3.

。

第十六条 双方因履行本合同而发生的争议，应协商、调解解决。协商、调解不成的，确定按以下第

种方式处理：

1.提交 仲裁委员会仲裁;

2.依法向人民法院起诉。

第十七条 双方确定：本合同及相关附件中所涉及的有关名词和技术术语，其定义和解释如下：

1.

;

2. ;

3. ;

4. ;

5. 。

第十八条 与履行本合同有关的下列技术文件，经双方以方式确认后，为本合同的组成部分：

1.技术背景资料： ;

2.可行性论证报告：

;

3.技术评价报告： ;

4.技术标准和规范：

;

5.原始设计和工艺文件： ;

6.其他：

第十九条 双方约定本合同其他相关事项为：

第二十条 本合同一式

份，具有同等法律效力。

第二十一条 本合同自国务院专利行政部门登记之日起生效。

甲方：

(盖章)

法定代表人/委托代理人：

(签名)

年

月

日

乙方： (盖章)

法定代表人/委托代理人：

(签名)

年

月

日

印花税票粘贴处：

(以下由技术合同登记机构填写)

合同登记编号：

1.申请登记人：

2.登记材料：(1)

(2)

(3)

3.合同类型：

4.合同交易额：

5.技术交易额：

技术合同登记机构(印章)

经办人：

年

月

日

中外技术转让合同

合同号：_______________________  签订日期：_____________________  签字地点：_____________________  一九_____年_____月_____日  前 言  本合同于×年×月×日在__________________签订.  甲方为：中国 ×公司  合同工厂：中国×厂（以下简称甲方）  乙方为：×国××公司（以下简称乙方）  第一章 合同内容  1.1 乙方同意向甲方提供制造合同产品的书面及非书面专有技术.用该项技术所生产的合同产品的品种，规格，技术性能等详见本合同附件一（略）.  1.2 乙方负责向甲方提供制造，使用和销售合同产品的专有技术和其它所有有关技术资料.技术资料的内容及有关事项详见本合同附件二（略）.  1.3 乙方负责安排甲方技术人员在乙方工厂进行培训，乙方应采取有效措施使甲方人员掌握制造合同产品的技术，具体内容见本合同附件三（略）.  1.4 乙方派称职的技术人员赴甲方合同工厂进行技术服务.具体要求详见本合同附件四（略）.  1.5 乙方同意在甲方需要时，以最优惠的价格向甲方提供合同产品的备件.届时双方另签协议.  1.6 乙方有责任对本合同项目甲方需要的关键设备提供有关咨询.  1.7 乙方应向甲方提供合同产品的样机， 铸件和备件， 具体内容详见本合同附件五（略）.  1.8 甲方销售合同产品和使用乙方商标的规定，见本合同第八章.  第二章 定 义  2.1 合同产品指本合同附件一中所列的全部产品.  2.2 蓝图指乙方制造合同产品目前所使用的总图，制造图样，材料规范及另件目录等的复制件.  2.3 技术资料是指为生产合同产品所必须具有的乙方目前正用于生产合同产品的全部专有技术和其它有关设计图纸，技术文件等.  2.4 标准指为制造合同产品向甲方提供的技术资料中，由乙方采用和制定的标准.  2.5 入门费指由于乙方根据本合同第一章1.2条，1.3条，1.4条，1.6条，1.7条规定的内容以技术资料转让的形式向甲方提供合同产品的设计和制造技术，甲方向乙方支付的费用.  2.6 提成费指在本合同有效期内，由于乙方所给予甲方连续的技术咨询和援助，以及甲方在合同有效期内连续使用乙方的商标和专有技术，甲方向乙方支付的费用.  2.7 合同有效期指本合同开始生效的时间到本合同14.3条规定的本合同终止时间的期间.  第三章 价 格  3.1 按本合同第一章规定的内容，甲方向乙方支付的合同费用规定如下：  3.1.1 入门费为美元（大写：美元）这是指本合同产品有关的资料转让费和技术培训费，包括技术资料在交付前的一切费用.入门费为固定价格.  3.1.2 合同产品考核验收合格后，甲方每销售一台合同产品的提成费为基价的×％.甲方向乙方购买的零件不计入提成费.  3.1.3 计算提成费的基价应是甲方生产合同产品当年12月31日有效的，乙方在×国×市公布和使用的每台目录价格的％.  3.2 乙方同意返销甲方生产的合同产品.返销产品的金额为甲方支付乙方全部提成费的％（百分之）.返销的产品应达到乙方提供的技术性能标准.每次返销的产品品种，规格，数量，交货期由双方通过友好协商确定.  返销产品价格按3.1.3条规定的提成基价计算，即目录价格的％.  第四章 支付和支付条件  4.1 本合同项下的一切费用，甲方和乙方均以美元支付.  甲方支付给乙方的款项应通过中国银行和×国××银行办理.  如果乙方向甲方偿还金额，则此款项应通过××银行和中国银行办理.  所有发生在中国的银行费用，由甲方负担.发生在中国以外的银行费用由乙方负担.  42. 本合同第三章规定的合同费用，甲方按下列办法和时间向乙方支付：  4.2.1 甲方收到下列单据，并审查无误后天内向乙方支付入门费美元（大写：美元）.  （a） 由乙方出具的保证函.在乙方不能按照合同规定交付技术资料时，保证偿还金额美元.  （b） 即期汇票正，副本各一份.  （c） 应支付金额为入门费总价的形式发票正本一份，副本三份.  （d） ×国政府～出具的许可证影印件一份.若乙方认为不需要出口许可证，则乙方应提出一份有关不需要出口许可证的证明信一份.  4.2.2 甲方收到乙方交付第一阶段产品的下列单据并审查无误后天内向乙方支付美元（大写：美元.）  （a） 即期汇票正，副本各一份.  （b） 商业发票正本一份，副本三份.  （c） 空运提单正本一份，副本三份.  （d） 乙方出具的第一阶段产品的技术资料，样机，铸件和备件交付完毕的证明信正，副本各一份.  4.2.3 甲方收到乙方交付第二阶段产品的下列单据并审查无误后天内向乙方支付美元（大写：美元）.  （a） 即期汇票正，副本各一份.  （b） 商业发票正本一份，副本三份.  （c） 空运提单正本一份，副本三份.  （d） 乙方出具的第二阶段产品的技术资料，样机，附件五规定的已交付完毕的证明正副本各一份.  4.2.4 合同产品第一批样机验收合格后，甲方收到乙方下列单据并审查无误天内，向乙方支付美元（大写：美元）.  （a） 即期汇票正，副本各一份.  （b） 商业发票正本一份，副本三份.  （c） 双方签署的“合同产品考核验收合格证书”影印本一份.  注：如果验收试验延迟并是甲方的责任，将不迟于合同生效后（时间）支付.  4.3 本合同第三章规定的提成费，甲方将在抽

样产品考核验证合格后按下述办法和条件向乙方支付：  4.3.1 甲方在每日历年度结束后天内，向乙方提交一份甲方在上一日历年度的每种型号的产品实际销售量的报告.  4.3.2 乙方每年可派代表到合同工厂检查和核实甲方合同产品实际销售量的报告，甲方将给予协助.乙方来华费用由乙方负担.如果汇总和/或报告中所列的合同产品数量在检查时发现出入很大，则甲乙双方应讨论此差距并洽商采取正确的措施.  4.3.3 甲方收到乙方下列单据并审查无误后的天内向乙方支付提成费：  （a） 即期汇票正，副本各一份.  （b） 商业发票正本一份，副本三份.  （c） 该年提成费计算书一式四份.  4.3.4 在合同期满年度内，甲方在合同终止后天内将提交一份最后销售合同产品数量的报告，以便乙方计算提成费.  4.4 按本合同规定，如乙方需向甲方支付罚款或赔偿时，甲方有权从上述任何一次支付中扣除.  第五章 技术资料支付  5.1 乙方应按本合同附件二的规定向甲方提供技术资料.  5.2 乙方应在机场或车站交付技术资料.机场或车站的印戳日期为技术资料的有效交付日期.甲方应在收到资料两周内，确认资料收悉.  5.3 第一阶段产品的技术资料，样机，铸件和备件：  5.3.1 在合同生效后的××周内，乙方必须发出一套篮图，一套二底图和一套标准.可以分批交货.  5.3.2 在合同生效后的××周内，乙方必须发出与第一阶段合同产品有关的全部技术资料，样机，铸件和备件.  5.4 第二阶段产品的技术资料和样机：  5.4.1 第二阶段开始日期后的×周内，乙方必须发出与第二阶段产品有关的一套篮图，一套二底图和一套标准.可以分期交货.  5.4.2 第二阶段开始后的××周内，乙方必须尽快发出与第二阶段合同产品有关的全部技术资料和样机，铸件和备料.  5.5 在每批技术资料或样机，铸件和备件发运后的小时内，乙方应将空运提单号，空运提单日期，资料编号，合同号，件数和重量电告甲方.同时乙方应以航空信将下列单据寄给甲方：  （a） 空运提单正本一份，副本二份.  （b） 所发运技术资料，样机，铸件和备件的详细清单一式二份.  5.6 若乙方提供的技术资料或样机，铸件和备件在运输途中遗失或损坏，乙方在收到甲方关于遗失或损坏的书面通知书后，应尽快不迟于×个月内免费补寄或重寄给甲方.  5.7 交付技术资料应具有适于长途运输，多次搬运，防雨，防潮的坚固包装.  在每件包装箱的内部与外表，都应以英文标明下列内容：  （a） 合同号  （b） 运输标记  （c） 收货人  （d） 技术资料目的地  （e） 重量（公斤）  （f） 样机，铸件和备件目的地  5.8 每箱内应附有详细装箱单一式四份.  第六章 技术资料的改进和修改  6.1 为了适应中国的设计标准，材料，工艺装备和其它生产条件，在不改变乙方基本设计的条件下，甲方有权对乙方的技术资料进行修改和变动.甲方必须将这些修改和变动通知乙方.乙方有责任在培训或技术指导时协助甲方修改技术资料，详见附件三和附件四.  6.2 甲方必须在型号后加注尾标，以示区别那些影响形状，配合或功能的修改，并通知乙方.  6.3 合同有效期内，双方在合同规定的范围内的任何改进和发展，都应相互免费将改进，发展的技术资料提交给对方.  6.4 改进和发展的技术，所有权属改进，发展的一方.  第七章 质量验收试验  7.1 为了验证按乙方提供的技术资料制造的合同产品可靠性，由甲，乙双方共同在合同工厂对考核的合同产品的技术性能和要求进行考核验收.如果需要，也可以在乙方工厂进行试验或重做.甲方可派指定的人员验证重复试验，乙方负责重复试验和乙方人员的费用，甲方负责甲方参加重复试验的人员和翻译的费用.具体办法见本合同附件七.  7.2 考核试验产品的技术性能应符合乙方提供的本合同中的标准规定，即通过鉴定.甲，乙双方签署“合同产品考核验收合格证明”一式四份，每方各执二份.  7.3 如考核试验产品的技术性能达不到附件规定的技术参数， 双方应友好协商， 共同研究分析原因，采取措施，消除缺陷后进行第二次考核验收.  7.4 如考核试验产品不合格是乙方的责任，则乙方派人参加第二次考核验收的一切费用，由乙方负担.如系甲方责任，该费用由甲方负担.  7.5 若考核试验产品第二次试验仍不合格时，如系乙方的责任，乙方应赔偿甲方遭受的直接损失，并采取措施消除缺陷，参加第三次考核，费用由乙方负担.如系甲方责任，该费用由甲方负担.  7.6 若考核试验产品第三次考核试验不合格时，双方应讨论执行合同的问题，如系乙方责任，则按合同9.8条规定，甲方有权修正合同.如系甲方责任，则由双方共同协商进一步的执行问题.乙方将根据甲方的要求，为改进不合格的样机提供技术咨询.  第八章  “合同产品”的出口和商标  8.1 甲方生产的“合同产品”可在中华人民共和国国内销售，可根据下列条件出口到其它国家：  8.1.1 甲方应首先与乙方协商，要求在乙方的销售/分配网所在地区安排销售（销售，分配网包括乙方子公司和代理商）.  出口销售的数量和项目将通过友好协商决定，若无法安排，则甲方可以自由出口，但是，甲方必须在完成交易后一周内，将项目，数量和购买商名称通知乙方.  8.1.2 在乙方销售/分配网不包括的地区，甲方可以自由销售.  8.2 对于甲方把“合同产品”装在中国的主机上出售到任何国家（包括在乙方销售/分配网所在地国家）的权利，乙方不得干涉.为维修中国出口的主机，甲方可以自由销售作为

共3页，当前第1页123

职责:

1. 方法确认、验证和转移流程的建立，维护和执行

2. 分析方法的验证，确认、转移;

3. 组织方法验证和转移中发生的实验室事件和偏差调查

4. 启动和审核所有与项目管理有关的变更(包括验证，方法和规格变化等)，跟踪CAPA及时执行

5. 负责项目生产使用的对照品、和色谱柱管理

6. 参与流程的维护和优化，确保人员执行流程

7. 确保人员经过培训合格上岗，并保证持续培训，进行人员考核

8. 组织人员及时完成数据复核，确保产品放行前完成相关偏差调查;

9. 确保检测使用方法经过确认、验证或转移;

10. 参与客户审计和政府审查，及时完成发现项的整改;

11. 及时跟踪项目进展，与客户加强沟通，建立稳定良好的关系;

12. 确保实验室安全和人员安全

13. 协助部门领导建设一个高效率的团队

14. 使团队每个成员的主动性、积极性和创造性发挥出来。

15. 使整个团队充满活力

任职资格:

1.药学或化学相关专业，硕士以上学历。

2.了解制药生产、检测和质量管理，熟悉GMP相关法规。

3.熟练掌握英文，口语流利，英文表达流畅

4.计算机良好

5.8年以上工作经验，其中具有方法开发团队管理经验3年以上，GMP分析团队管理经验5年以上

6.具有良好的工作协调和沟通能力

7.通过科学的推理确定问题、收集信息、了解事实、得出正确有效结论。

8.项目管理和跟踪能力

9.进行预算和资产管理，控制实验室费用。

10.指导监督下属工作

11.对下属员工有工作分配、考核、激励的责任。

信息技术咨询服务合同

甲方(客户)：_________

地址：_________________

邮码：_________________

电话：_________________

乙方：_________________

地址：_________________

邮码：_________________

电话：_________________

甲乙双方根据国家对有偿信息发布的有关规定，签订本合同，并共同遵守。

一、甲方委托乙方于_________年_________月_________日至_________年_________月_________日期间在_________所属的网站或刊物上发布有偿信息服务。本合同所指的有偿信息服务包括：文字、图片及其他多媒体形式。

二、样稿来源：□甲方提供;□乙方设计后经甲方确认(需要额外收费)。

三、乙方有权审查信息内容和表现形式，对不符合法律、法规的内容和表现形式，乙方可要求甲方作出修改。

四、甲方对委托乙方发布的经济信息的合法性承担全部责任，并承诺对因此给乙方造成的损失承担赔偿责任。

五、有偿信息服务单价及报价

1.首页通栏图文信息：_________SWF/GIF□_________元/月;

2.标准横幅图文信息：_________SWF/GIF□_________元/月;

3.首页图标图文信息：_________SWF/GIF□_________元/月;

4.文字连接_________个字以内文本□_________元/月;

5._________招聘频道广告_________字以内文本□_________元/月;_________元/篇，送招聘栏目图标广告_______月。

甲方(盖章)： 乙方(盖章)：

代表受权人(签字)： 代表受权人(签字)：

年 月 日 年 月 日